By sticking cellophane tape to a balloon before popping it, the tape helps prevent the balloon from bursting loudly and creating a sudden noise. The tape absorbs some of the energy from the popping balloon, reducing the noise and making it a bit quieter.
The tape acts as reinforcement and prevents the hole from the pin to become a rip that bursts the balloon. Without the tape stuck onto the balloon the needle prick would allow the rubber tension to rip itself apart because of the air pressure stretching the rubber which would be in tension. The tape stops the balloon being able to split and so it doesn't burst. It used to be a kids trick to put 2 pieces of tape on opposite sides of a balloon and then push a long knitting needle right through the balloon without bursting it.
You may hear a bang and the balloon shreds itself. Alternatively, depending upon the properties of the rubber, the balloon may become airborne with the knot leading the way. But if you place a piece of cellulose tape on the balloon, you may puncture it through that without the bang!
When you insert a needle into a balloon, it creates a small hole. The air inside the balloon escapes gradually through this hole, preventing the balloon from popping. The pressure inside the balloon decreases as the air escapes, relieving the stress and preventing a sudden burst.
Tape can provide additional support to the balloon, distributing the stress caused by the pressure inside the balloon more evenly. This reduces the chances of the balloon popping, as the tape reinforces the material of the balloon, making it less likely to burst under the pressure.
The 'popping' sound of a balloon disintegrating is made by the sudden expansion of air when the skin is damaged. The compressed air within is then able to escape. One interesting variant of your 'water' experiment, is to stick a bit of cellulose tape to the balloon, and then you'll find that you may puncture the balloon; through the tape; without it popping! It will eventually deflate however.
Dick Drew invented cellophane tape in 1930. Not quite done after creating masking tape, he wondered why one couldn't just stick an adhesive to cellophane. He also created the Scotch brand.
Scotch tape was not invented in Scotland, it is merely a brand name for cellophane tape. Shrink-wrap is made from cellophane.
The tape acts as reinforcement and prevents the hole from the pin to become a rip that bursts the balloon. Without the tape stuck onto the balloon the needle prick would allow the rubber tension to rip itself apart because of the air pressure stretching the rubber which would be in tension. The tape stops the balloon being able to split and so it doesn't burst. It used to be a kids trick to put 2 pieces of tape on opposite sides of a balloon and then push a long knitting needle right through the balloon without bursting it.
Normally, When you prick a balloon with a needle the hole the pin makes creates a weak point that continues to tear as the pressure inside the balloon attempts to escape. ( I.E. To equalise the pressure inside and outside the balloon ) That is the balloon bursting... The piece of Scotch Tape, however, holds the area around the pinhole together stopping this tearing and preventing the balloon bursting.
http://www.wisegeek.com/what-is-cellophane-tape.htm
You may hear a bang and the balloon shreds itself. Alternatively, depending upon the properties of the rubber, the balloon may become airborne with the knot leading the way. But if you place a piece of cellulose tape on the balloon, you may puncture it through that without the bang!
"Cellotape" is the generic colloquial for "cellophane tape", most frequently identified in the US by the brand name "Scotch tape".
Many may use "scotch tape" as a generic term is typically used to refer to cellophane tape of any brand. In conversation, yes, chances are the person asking for "scotch tape" is referring to a cellophane or transparent tape such as that used for wrapping gifts.In reality, the "Scotch" name is in fact a registered trademark of 3M corporation and is the brand name of the original product. The Scotch Brand is applied to various forms of tape, and in fact was originally applied to a masking tape (not cellophane).To help combat trademark genericization, 3M markets its products today as "Scotch Brand Tape."
nicrobiology
When you insert a needle into a balloon, it creates a small hole. The air inside the balloon escapes gradually through this hole, preventing the balloon from popping. The pressure inside the balloon decreases as the air escapes, relieving the stress and preventing a sudden burst.
You can effectively stick a balloon arch to a wall by using removable adhesive hooks or tape. Make sure to clean the wall surface before attaching the arch to ensure a strong hold.
To get a balloon arch to stick to a wall effectively, you can use removable adhesive hooks or double-sided tape. Make sure to clean the wall surface before applying the adhesive to ensure a strong hold.