because it has more watts
Yes, a lamp will typically appear brighter when it is closer to the energy source. This is because the light intensity decreases as the distance from the source increases. Placing the lamp closer to the energy source allows for more light to reach the lamp and make it appear brighter.
The brightness of a lamp is directly related to its performance because a brighter lamp provides more light output, which can improve visibility and overall effectiveness in lighting up a space.
A Japanese lamp clock typically uses a special lamp inside the clock to create a soft, warm glow to indicate the time. The lamp is connected to an internal mechanism that controls its brightness to display the time in a subtle way. Users can often customize the brightness levels and colors of the lamp for personal preference.
A filament lamp produces light by converting electrical energy into heat and then light. It acts as a resistive load in the circuit, meaning it resists the flow of current and causes the filament to glow and produce light.
A lamp refers to the entire lighting fixture that holds the bulb and provides light, while a bulb is the actual light-emitting component that fits inside the lamp and produces light when powered. In other words, the bulb is the source of light, while the lamp is the structure that houses and supports the bulb.
Because the filament of a 25-W lamp has a higher resistance than that of a 60-W lamp and, therefore, will experience a greater voltage drop -the lamp with the voltage drop closer to its rated voltage (in this case, the 25-W lamp) will be the brighter.
Oh, dude, let me break it down for you. If you connect a 40W bulb and a 60W bulb in series, the 60W bulb will glow brighter because it has a higher wattage rating. It's like having a race between a tortoise and a hare - the hare (60W bulb) is gonna shine brighter than the tortoise (40W bulb). So, yeah, the 60W bulb takes the spotlight in this series connection scenario.
Yes, a lamp will typically appear brighter when it is closer to the energy source. This is because the light intensity decreases as the distance from the source increases. Placing the lamp closer to the energy source allows for more light to reach the lamp and make it appear brighter.
the faster the speed of the bicycle,the brighter the lamp
If the voltage supplied to the lamps is its operating voltage both lamps will have relatively the same output in brightness. If the 60 watt 110 volt lamp is used on a 220 volt supply, it will glow very brightly and then the lamp's filament will burn open. If the 60 watt 220 volt lamp is used on a 110 volt supply, the lamp will glow at half brightness, but it will last for a very long time before the filament burns open.
Several ways. Firstly make sure you are getting voltage to the glow plug. The easiest way is to connect a 12v lamp between the battery negative and the top of the glowplug. Turn the ignition on and the lamp should light. If lamp does not light the glow plug relay circuit has a problem. If lamp test OK remove it from the negative terminal and connect to the positive terminal of the battery. If lamp lights, glow plug OK. OR turn the ignition on for ten seconds and switch off again. feel the connector the top of the glow plug and it should be warm. OR disconnect wire and check with a meter between the glow plug contact and the engine block, the ohmic value should be less than 10.
stars are planets and it shines because light is reflected so...depends on what kind of lamp ur talking about
If the socket threads of the lamp are the same then yes the bulbs can be interchanged. The 5 watt bulb will glow brighter than the 4 watt bulb. If by a 4 watt light you mean a 4 watt fixture, then it is not recommended to place a larger wattage lamp in a fixture that is rated by the manufacturer at a specific operating wattage
For a lamp to operate at its rated power, it must be subject to its rated voltage. The lower the voltage, the lower the resulting power. In fact, a small drop in voltage will cause substantial drop in power. Higher 'wattage' lamps have lower resistance values than lower 'wattage' lamps.So, if you put two lamps in series, the greater voltage drop will appear across the lamp with the greater resistance. In your example, that means the 100-W lamp will be subject to the greater voltage drop, and its loss of power will be less than that of the 200-W lamp. So the lower power lamp will be the brighter of the two.
Yes, but you will get a higher wattage output than 800 watts, this means that the lamp will glow brighter. This connection will also shorten the life of the lamp because of the higher voltage. When you state "plug", it suggests that the connection will not be made if the plug can not fit into the receptacle.
The brightness of a lamp is directly related to its performance because a brighter lamp provides more light output, which can improve visibility and overall effectiveness in lighting up a space.
Take 240V Lamp first check the voltage at Phase w.r.t neutral if lamp glows it means present voltage is OK now check the voltage w.r.t earth i.e. between phase & Earth point then lamp will glow. Now check between Neutral & Earthing Lamp should not glow. If these conditions are fulfill then your Earthing is OK.