answersLogoWhite

0

It is difficult to pull a plunger off a surface due to the creation of a vacuum seal. When the plunger is pressed against the surface, the air inside the suction cup is forced out, creating a vacuum. This vacuum seal creates a strong grip between the plunger and the surface, making it hard to pull off.

User Avatar

AnswerBot

1y ago

What else can I help you with?

Continue Learning about Physics
Related Questions

How do you get Zack off the shower curtain pole in riddle transfer?

In "Riddle Transfer," you can get Zack off the shower curtain pole by using the plunger to knock him down. First, you need to obtain the plunger from the bathroom. Once you have it, aim at Zack while he's hanging on the pole, and use the plunger to pull him down. This will successfully get him off the pole and progress the game.


How do you pull down the plunger in The Cat in the Hat game for PC?

Jump up onto the plunger. Jump up and press CTRL when he's in the air and the cat will swing his open umbrella underneath him, landing on the umbrella and set off the plunger. You will need to use this same move on other things later in the game.


Can you use a PIN with no trace left behind?

I theory, yes. but it may be difficult to pull this off in reality.


1992 Chevy caprice brake light stays on but the brakes are off?

brake light plunger switch on the brake pedal maybe faulty, remove it and connect the two wires together and pull apart and see if lights go on and off


What made Houdini's job difficult?

His dangerous illusions and tricks you have to be very talented to pull those off and not die.


How do you make a slurry for dogs medicine?

The easiest way I have found is to pull the plunger out of a large syringe (60 cc works great). Drop the tablet(s) into the front of the syringe and put the plunger back in. Run tap water from a faucet and stick the tip of the syringe into the running water. Pull back on the plunger to get 20-30 ccs of water in the syringe - it should be about half full. Turn off the faucet and place your index finger over the tip of the syringe. Shake until the tablets are dissolved, then use the syringe to "inject" the slurry into your dog's mouth.


If a 97 Toyota Camry is dented below the driver's side door window and the window will not close would you need to replace the door?

Get a friend to use a plumbers helper or plunger to stick on the door and pull it off and see if it is possible to pull the door skin out enough to free the window.


How do you remove brake booster 1980 corvette?

There are four bolts holding the booster to the firewall, two holding the master cylinder to the booster, and and a retaining clip or cotter pin on the plunger rod to pedal attatchement. The Upper booster mounting bolts are the most difficult to remove. I had to Remove steering the column assembly, You can remove the entire dash, (which is what I did) or just the instrument cluster. Then , using a long extention, the bolts are easily accessed. There is no need to disconnect the brake fluid lines, just pull the master cylinder off to the side with a bungy cord. Remove the retaining clip on the pedal, then the four mounting bolts. It should pull right out the front..When re assembling, lube the push rod plunger, (its a short 2" or so rod)make sure its in place when putting the booster back in the firewall,, the grease will help the plunger stick where it needs to be alsol.. You'd be surprized, mine fell off in the box, (the plunger) and almost got overlooked! Hope this helps


How do you pull a heist?

Because of increased security features and security technology, it is very difficult to pull off a heist nowadays. Also, those who are able to pull a heist are more often than not apprehended by law enforcement.


Why do the brake lights constantly stay on whether the vehicle is on or off?

There is a brake light switch mounted high up on the brake pedal. The switch has a plunger which is released (extends) when you step on the brake pedal. This completes an electrical circuit. The switch has either come loose from where is it mounted so that the plunger is released all the time or part of the plunger has broken off. This has the same effect as having the plunger released.


How to effectively use a power plunger for unclogging drains?

To effectively use a power plunger for unclogging drains, follow these steps: Insert the plunger into the drain opening. Turn on the power and apply pressure to create a strong suction. Move the plunger up and down vigorously to dislodge the clog. Repeat as needed until the drain is clear. Turn off the power and remove the plunger from the drain.


Two energies the sun gives off are?

one is nuclear energy another is gravity pull the energy onto the surface