0
What else can I help you with?
What is the weight of cp brass bib cock?
The weight of a CP brass bib cock can vary depending on its size and design. On average, a standard brass bib cock typically weighs around 0.5-1.5 kilograms.
What is the difference between blowing a cock and sucking a cock?
Both phrases are vulgar terms referring to oral sex acts involving a penis. "Blowing a cock" typically refers to oral stimulation using breath and mouth movements, while "sucking a cock" specifically highlights the action of drawing or pulling with the mouth.
How do you make and use cockring?
To make a cock ring, you can use materials like silicone, leather, or metal. Measure the circumference of the base of the penis when erect and cut the material to size, making sure it's snug but not too tight. To use it, slide the cock ring down to the base of the penis when erect to help maintain a firmer and longer-lasting erection. Make sure to remove the cock ring after about 20-30 minutes to avoid discomfort or injury.
Will a cock ring make you last longer?
A cock ring can help maintain an erection by restricting blood flow, which may lead to longer-lasting sex. However, it does not directly affect stamina or delay ejaculation. It's important to communicate with your partner and engage in other techniques to improve sexual endurance.
How much is 1 lb?
1 pound = 0.45359237 kilograms noo it is 2.2kg =1pound i recall; 1 pound = 16 ounces
Why it is necessary to turn off the gas with the gas cock rather than with the valve on the burner?
When you leave the gas cock open when you turn off the burner valve, and someone moves the burner to another gas port, there would be a serious gas leak until you turned off the gas at the gas cock.
What is gas cock in the Bunsen burner?
A gas cock in a Bunsen burner is a control valve that allows the user to adjust the flow of gas to the burner. By turning the gas cock, the user can increase or decrease the flow of gas, which in turn alters the flame intensity and temperature of the burner.
What is the functional difference between cock and valve?
The term cock and valve are used interchangeably in the English language. The term cock has in large been replaced with valve with no functional difference between the two.
Do you have details on a seacock with a tighten down valve opposite side of shutoff valve?
I have a Stuart sea cock bronze with a nut that secures the on off valve spindle. This is fairly old fitted to me Sabre 27 built 1978. It is still in service and can be re-furbished if necessary.
What is a ball cock?
The valve that shuts off the water in a toilet cistern is known as the ball-cock. It is operated by a hollow ball attached to an arm, once the ball floats to a certain level, the valve shuts off the water. This action prevents water flowing out of the over-flow pipe to the outside. The ball and valve is known as the ball-cock.
Dump valve hdi?
Why do you want one, just makes you look a cock.
What is an isolation valve and fill valve in a toilet?
An isolation valve isolates the fixture so one can disassemble the fill valve (ball -cock) and make necessary repairs. Also the isolation valves on most fixtures are globe pattern type so one can throttle the volume entering the fixture to prevent hydraulic shock and prevent excessive noise
What is the gas cock?
The gas cock, also called a petcock, is a small valve at the bottom of a motorcycle's gas tank that allows to shut off the flow of fuel to the engine.
What does the try cock valve do?
A try cock valve is a small valve used in steam and water systems to allow for the sampling or draining of fluid from a pipe without fully opening the system. It provides a means for operators to check for the presence of water or steam and assess the system's condition. By using a try cock, maintenance personnel can determine if the system is working correctly or if there are any issues that need attention, all while minimizing the risk of leaks or pressure loss.
What is the use of pinch cock valve?
A pinch cock valve is used to control the flow of fluid in a flexible tubing by pinching the tube closed. It is commonly used in laboratory settings or in medical applications where precise flow control is required.
How do you replace a flushing tower on American standard toilet?
There is no such thing as a "flushing tower" in America you have to go to France and ask for directions about changing a Douglas valve or fluid intake valve (Ball cock)
What is a corporation stop use for?
A corporation stop is a cock (stopcock) controlling the flow of water or gas from a main to an individual customer. It is also called corporation cock. It is located where the service lateral is tapped into the main, so it is usually not accessible without digging up the street. A curb stop is also a cock controlling the flow of water or gas from a main to an individual customer, but it is accessible in a valve box or valve can near the curb line, or inside the meter box.
