This is to reduce the chances of the burner accidentally tipping over. Knocking over a lit Bunsen burner could obviously have very bad results.
Not usually. Heavy is an adjective. It modifies a noun. e.g . "a heavy cat." Heavily is an adverb. It modifies a verb. "He sighed heavily." There are, however, rare uses of 'heavy' as an adverb, most commonly where the verbs 'weigh' and 'lie' and 'hang' are used.
Heavy weight is typically considered to be any weight that is challenging for an individual to lift or move, usually in the context of weightlifting or strength training. The specific definition of heavy weight can vary depending on a person's fitness level, experience, and capabilities.
Pushing something heavy may cause temporary compression or flattening of the skin on the fingertips, which could potentially alter the visibility of fingerprints. However, this effect is usually temporary and the fingerprints should return to normal once the pressure is removed.
Tornadoes can be associated with hail and heavy rain, but their formation does not involve precipitation. Tornadoes form from severe thunderstorms where strong updrafts of warm, moist air create a rotating column of air that extends to the ground.
The prefix for "heavy" is "over-".
To keep it from tipping over while in use.
The function of a base in a Bunsen burner is to provide stability and support for the burner during use. The base is typically made of a heavy metal, such as cast iron, to prevent the burner from tipping over. It also helps to dissipate heat generated during combustion, reducing the risk of accidental burns or fires. Overall, the base plays a crucial role in ensuring the safe and efficient operation of the Bunsen burner.
A machete is a broad heavy knife.
A machete is a broad heavy knife.
BarrelThe barrel of a Bunsen burner is a metal tube that screws onto the base of the burner, with small holes called air intake openings in the bottom that let air into the barrel. As outlined by the Eastern Illinois University's Equipment Guide when a Bunsen burner is operational, natural gas draws air into the barrel as it passes the air intake openings--the mixture of air and gas is ignited at the top end of the barrel.CollarThe collar of a Bunsen burner is located around the air holes on the bottom of the barrel. The collar's function is to increase or decrease the amount of air going into the barrel; this is done through a screw mechanism. The typical action is three full counterclockwise turns for the maximum air intake and clockwise turns to close, or lower, the air intake.Gas Flow ValveThe gas flow valve of a Bunsen burner is attached to the base, directly underneath where the barrel screws on. The gas flow valve is responsible for letting gas into the barrel and can be adjusted in a similar manner to the collar--three counterclockwise turns for full gas, and clockwise turns for lesser gas or to turn the burner off completely.Gas Intake TubeThe gas intake tube is attached to the base and extends to the gas flow valve. The intake tube is corrugated and tapers at the end. This is so that an air-tight fit can be achieved with the gas pipe that is attached to the gas intake tube, making sure that there is no leakage of gas.BaseTypically, the base of a Bunsen burner is hexagonal (has six sides) and is usually 1 inch or less wide. A base has upward-slanting metal fixings on two sides that connect just above the gas flow valve and just below the gas intake tube. The base is designed to be heavy and sturdy to minimize incidents of Bunsen burners tipping over.
The wide metal base of a Bunsen burner provides stability and prevents it from tipping over during use, especially when supporting the weight of a heavy gas tank or when adjusting the flame height. It also helps to dissipate heat and reduce the risk of accidental burns or fires by providing a larger surface area for heat distribution.
The ring stand used in chemistry is typically called a "retort stand." It is a metal rod with a heavy base that holds various clamps and rings used to support laboratory glassware or other equipment during an experiment.
heavy broad jackets
Larger the area smaller the pressure. School bags usually have broad straps so that the weight of the bag may fall over a large area on the shoulder producing less pressure and less pressure, it is comfortable to carry heavy bag.
To spread the weight out more evenly and to take a heavier load.
To spread the weight out more evenly and to take a heavier load.
Car oil is much too viscous and heavy for a home oil burner, which uses light oil similar to kerosene. This is apart from the used oil being rich in black material from the combustion process in the engine. It will damage your burner.