0
What else can I help you with?
What happens if only half the outlets work on run the main breaker?
assuming you have reset all of the other circuit breakers as well, look for a ground fault interrupt outled (GFI). It will have a small red and black button in the middle. It will probably be near water, in bathroom kitchen or garage. Reset it and the other outlets should work again.
Are Federal pacific breakers allowed by any insurance company?
I live in Dallas and I have found no insurer who cares if you have FB breakers. My Farmers agent was not aware of the issue at all.
Why do two separate breakers control the same outlets?
The only time 2 beakers are run to one outlet is if the outlet is 240V. The breakers should have handle-ties connected to them to ensure that both breakers trip in the event of an overload. Nope its not 240 either,cause it continues to other outlets the same way.and can plug 110 accesories into them. I have come accross this everywhere. In rooms without a ceiling light, one half of a duplex receptacle is a switched lighting circuit and the other is a always on receptacle.
Can a house be connected in series circuit?
The breaker panel. Breakers are placed in series with all outlets.
Why do All the electric sockets in a room not work?
Some fuses/circuit breakers blown? Some cables not connected?
When the test button is pressed on a gfci outlet it sparks and trips two breakers in the main panel What could be the problem?
The test button should only trip the GFCI. The fact that it is tripping two breakers indicates that somehow both breakers are feeding your GFCI circuit. I have seen this when there was a wiring error and two circuits were joined in an outlet that was connected to a breaker and through the GFCI outlet. To troubleshoot determine which outlets are effected when both breakers are off. Pull outlet from box and if there are two feeds remove one from outlet and run a toner on wire left on outlet to panel and one off outlet to panel. The GFCI could block the toner so if one side of the outlet does not tone back to panel check at GFCI. There must be two paths to your electric panel for the two breakers to trip and the GFCI may be faulty as well. Another way to check is to have the GFCI reset and both breakers on. Check each outlet that you have identified as being on GFCI noting that they can be in different rooms. With all outlets working turn off one of the tripped breakers. See if any outlets so off. If not turn off the other breaker and turn on the first breaker. If power is still present then the outlets are being fed by both breakers.
Are all universal adapters the same?
No they are not all the same. Universal adapters come in many different voltages and work in different outlets.
Who sings you can live beside the ocean and leave it all behind Swim out past the breakers watch the world go by?
It's "We can live beside the ocean/ Leave the fire behind /Swim out past the breakers/ Watch the world die." The song is called "Santa Monica" by Everclear.
Do both the breakers and the outlets need to be GFI if you are running two 15 amp GFI circuits?
If you're using a GFCI breaker then the entire circuit will be protected by just the breaker alone. Every receptacle, switch, etc on that breaker will utilise the GFCI protection. You may have problems with it tripping if you plug in a motor (vacuum, etc) on the circuit.
How can you tell if a house has GFCI breakers?
GFCI breakers are required by electrical code for all new and modified residences post 1984.Ground Fault Circuit Interrupters detect extremely small current fluctuations on the return side Neutral / Ground and cause the circuit to trip. Highly important in moist environments.To answer the question: GFCI breakers are required in all bathroom, garage and external outlets. To determine if it is a GFCI there will be a switch in the center typically of the outlet that says set/reset. Multiple outlets in a garage or outside may be wired in parallel and controlled by a GFCI breaker located in the main power panel. Remember use of a non-GFCI outlet in a moist environment is courting trouble and you or someone else may be the recipient.Answer for USA, Canada and countries running a 60 Hz supply service.GFCI breakers are not required. GFCI protection is required and you may choose whether to install GFCI breakers or GFCI receptacles. GFCI breakers, just like GFCI receptacles, will have a Test button. The breaker also will have the neutral attached to it on an appropriate terminal and an additional wire carrying the neutral current to the neutral bar.GFCI protection is required in all bathrooms, garages and other unfinished portions of a house including crawl spaces, unfinished basements, outside, and anywhere within 6 ft of the outside edge of a sink. -- SparkfighterAs always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
When would it be a better idea in a residence to install a GFCI breaker instead of an GFCI outlet?
GFCI Breakers are quite a bit more expensive than a GFCI outlet. More often than not a typical residence will need only a handful of GFCI outlets that combined together will be cheaper than a GFCI breaker. If you need to protect a series of outlets with GFCI protection you can simply connect the rest of the outlets on that same circuit downstream from the first outlet on the line and make that the GFCI. All you have to do is connect all the other outlets to the LOAD side of the GFCI outlet. If a GFCI fault occurs in any of the outlets down stream they will trip that very first GFCI plug you placed and keep you safe.
Name 5 important safety rules to keep in mind with electricity?
Always assume that all wires are live and handle them with care, using insulated tools when necessary. Keep electrical devices and outlets away from water to prevent shock hazards. Never overload outlets or power strips, as this can lead to overheating and fires. Regularly inspect cords and plugs for damage and replace them immediately if any wear is visible. If you experience a power outage, avoid opening circuit breakers or fuses without proper knowledge and safety equipment.
