answersLogoWhite

0

The production of silverplated cutlery on an industrial level began in Germany in the middle of the 19th century. Two factors limited the output:

1. Access to electrical power was very limited at the time.

2. Electrical current was quite weak compared to the present day.

After some experimenting, engineers achieved the best results if they used a small bath, put one dozen table spoons and one dozen table forks in it, used 90 Grams of fine silver and then immersed the pieces until the silver anodes were dissolved and the silver had firmly settled on the cutlery. This took many hours and in the beginning made the finished pieces quite expensive. The engineers discovered that a little more than half of the 90 Grams used was spread on the 12 spoons (as they have a bigger surface than the forks), a little less than half was spread on the 12 forks. Using a larger bath would require a much longer plating process, which would have made the process even more expensive. To use more than the 12 + 12 pieces in a bath would result in:

1. The pieces closest to the silver anodes would get a much thicker plating.

2. The pieces farthest from the anodes would get a very thin plating.

So the thickness of the silver layer would differ considerably.

Using 12 + 12 pieces as described above and 90 Grams of fine silver became a standard in Germany. To document this, the "90" was punched on the pieces. If companies wanted to produce cheaper cutlery, they used less silver, 60 Grams, 40 Grams or even 20 Grams, which made the plating very thin. Some used more, 100 or 150 Grams. Pieces were punched accordingly "60", "40", "20", "100" etc.

The plating process was adapted to other pieces of flatware and cutlery; knife-handles, smaller spoons, serving pieces etc., so that the silver layer on them was as thick as on the table spoons and table forks. As the same standard process was used, they all were stamped with the "90". New techniques made it possible to plate more pieces in bigger baths in shorter time, using much larger silver anodes. However, the thickness of the plating remained the same , so the marks remained the same.

When plated cutlery became more affordable and more and more customers bought it, they began to ask how much pure silver their flatware actually "contained". Manufacturers realized that they could use the answer as a method to promote sales and started punching a further mark that roughly provided the actual gram weight of the silver that coated the pieces. Unfortunately they used two different systems:

1. Pieces that usually come in a dozen (table- forks /-spoons / -knives, coffeespoons etc.) are punched with the weight of silver used for plating a dozen pieces. So tableforks and tablespoons were marked with a "45", smaller pieces were punched a lower figure (e.g. "35"), as less silver was needed to give them the same thickness of plating.

2. Pieces that usually came singly or in pairs (serving pieces) were punched with the weight of silver on a single piece.

Examples:

If you have a table spoon marked "90" and "45" it means: the standard process as described above was used, on one spoon roughly 1/12 of 45 Grams

(ca. 3,75 Grams) of fine silver were spread. If you have a sugar tong marked "90" and "2" it means: again the standard process was used, 2 Grams of fine silver were used to coat the piece. If you have a pair of salad servers, each piece marked "90" and "4" it means: again the standard process was used, on each piece 4 Grams of fine silver were used.

This German system of silverplate marking has been adopted by other European countries, and is sometimes seen on Dutch, Danish and Austrian silverplate.

User Avatar

Wiki User

∙ 15y ago
User Avatar

What else can I help you with?

Trending Questions
According to the Insurance Institute of America a family of four spends between400 and 3800per year on all types of insurance. Suppose the money spent isuniformly distributed between these amounts.Wha? What is the major difference between a mathematical model and an econometric model? Three balls are drawn one at a time without replacement from an urn that contains four white and six red balls what is the probability of drawing a red ball on the third draw? What are the individual measurements on a line graph called? How does a doorbell makes a continuous ring? What does mg dl mean? What does signifigant amount of money mean? What shape has 6 edges? Suppose you roll 2 six-sided dice one white one red Find the probability that the number showing on the red die is greater than the number showing on the white die? What should you do before you revise a prediction? Is radius of gyration depend on mass? If you flip a coin 50 times and you get 28 for heads what percent is it? Which media element is best suited to helping the readers of a procedural document compare factual information such as statistics? How many kilograms of cocoa beans makes 1 ton? What is the Probability of having 0 or 3 boys in a 3 child family? What do you understand by tabulation in statistics for management subject? What are the odds of getting pregnant at 50? Why batch processing is called a time dependent? Do skinny boys have bigger penises than fat boys? What is the bottom line of a bar graph called?