answersLogoWhite

0

📱

Computer Hardware

Computer hardware is a general term used to refer to all the physical parts of a computer. Internal hardware devices include hard drives and motherboards, while external hardware devices include monitors, mice, keyboards, and printers.

11,849 Questions

What is COM1 used for?

COM1 is seldom used for anything these days, and may not even be mapped to a physical device on newer systems. Its primary purpose is/was to serve as a communications port, either to an internal or external modem, or as a connection into a mainframe computer. It has also seen some use as a general purpose expansion port and been used to attach mice, printers, and cameras to a computer.

ECC memory is more reliable than non-ECC memory?

ECC cost more but is more reliable than non-ECC memory. TRUE

Replace the tip on the toshiba tablet pen?

After spending tons of time trying to find instructions from Toshiba or the internet, I finally figured it out. The tip just pulls out. You can do it with a pair of pliers or tweasers or whatever. It is simply a friction fit. You can then put a new tip back in the pen and push it into place. When you get your new tablet, you get 5 or 6 replacement tips and a little ring. It turns out the ring is a simple tool for removing your tips, and works like tweasers. Very simple very easy. It would be nice if Toshiba posted instructions for this operation.

Where do all components of the computer attach?

Download a Manual from the motherboard manufactures web site.This will tell you where everything goes with pictures usually. Hope this helps

What are the 3 categories of Front Side Bus signals?

1. Data Signal Group

2. Address Signal Group

3. Common Clock Signals

What is an output unit?

anything that sends a signal out of the computer. Such as a monitor or printer. your keyboard and mouse are the input

or

It display the data,program,pictures on the screen.it points the data,program,pictures on the point.it point the graphs on the graph plotter.it produce music etc on the speakers.it shows the data on the multimedia.(Anis kazmi)

What is the best laptop to use for editing anime music videos?

maybe an Apple computer, because they have a movie editing thing that might be better than a PC's windows movie maker.

What is ROMPAQ?

PCs made by COMPAQ prior to 2002 i.e before HP acquired COMPAQ

Can you upload photos from SD card to PC?

Yes you can Have to a USB adapter for memory card reading or built-in go to your computer. First go on my computer you can go to start menu for older windows version or windows 8 user need go desktop my computer. Second click your sdcard but noted it have varies drive letter normally it's E. Third found the photos you wants drag and drop where the photos you want you done. if computer that where all your storage devices is at.

When might you need to disable ECP mode for a parallel port?

# If you are having problems with resource conflicts, you could try disabling ECP mode for the parallel port. EPP mode gives good results and does not tie up a DMA channel.

What is SanDisk?

It's a company that sells USB flash disks. "San" refers to "without" and Disk... well the company name just means without disk.

What hardware is necessary to run Dragon Software?

the necessary step are to have at least the requirement's of ram

Which is better GPRS 384kbps modem or PCI modem 56kbps?

The GPRS modem has a much greater bandwidth. It would be better suited to most tasks. However it would depend on what the connection was intended for. The wired modem may provide better reliability and lower ping in some situations.

Is thumb drive a magnetic storage media?

Nope. Flash drives don't use magnetic storage.

What is a optiplex?

Optiplex is a Dell company product. Basically desktop computer

Explain the main difference between overclocking and throttling?

Overclocking is the process of running components past their specified rates. Throttling is the process of reducing the rate at which the component runs. Throttling is often included in the design specs of a processor, so there is usually no danger in it. When you run components below the rate that they are rated for (even for throttling limits), this is generally known as underclocking.