Dodge Nitro

The oil filter on a 2007 Dodge Nitro is located on the underside of the engine, toward the front of the vehicle. To access it, you'll typically need to lift the vehicle for better clearance. It's positioned near the oil pan and can be identified by its cylindrical shape. Always ensure the engine is cool before attempting to change the oil filter.

To reset the service light on a 2008 Dodge Nitro, turn the ignition key to the "On" position without starting the engine. Press the gas pedal three times within 10 seconds. Turn the ignition off, then start the engine to ensure the service light has been reset. If the light remains on, you may need to check for any existing issues or repeat the process.

In a 2007 Dodge Nitro, the fuse for the cigarette lighter is located in the fuse box under the dashboard on the driver's side. Specifically, you should check the fuse labeled "CIG" or "CIGAR," which is typically a 20-amp fuse. If the lighter is not working, inspecting and replacing this fuse may solve the issue. Always refer to the owner’s manual for the exact fuse location and specifications.

The 2007 Dodge Nitro has two fuse boxes. One is located under the hood in the engine compartment, while the other is found inside the vehicle, typically beneath the dashboard on the driver's side. These fuse boxes contain fuses and relays for various electrical systems in the vehicle. Always consult the owner's manual for specific fuse locations and functions.

On a 2007 Dodge Nitro, the Bank 1 O2 Sensor 1 is located on the exhaust manifold, upstream of the catalytic converter. It is positioned on the driver's side of the vehicle, near the engine. This sensor monitors the oxygen levels in the exhaust gases to help manage fuel injection and emissions.

In a 2007 Dodge Nitro, the relay for the air conditioning (AC) system is located in the Integrated Power Module (IPM), which is found in the engine compartment. To access it, open the hood and look for the black box near the battery. The specific relay for the AC is typically labeled on the underside of the IPM cover for easy identification.

The Jeep Liberty KK and Dodge Nitro skid plates are similar but not identical. While they share a common platform, the specific design and mounting points can differ due to variations in vehicle specifications and intended use. It's essential to check compatibility with the specific year and model before using them interchangeably. Always refer to manufacturer specifications or consult with a professional for the best fit.

I do not see aftermarket replacement rear wiper blades nor rear wiper refills listed in the aftermarket wiper catalogs for the 2008 Dodge Nitro. This would possibly indicate that the rear wiper was a proprietary Dodge technology/design and you may have to go to the dealer for the parts and possibly labor. Before doing this (because its usually a little more expensive going through the dealer), you may want to visit some internet forums and see if there's other ideas out there. Google "dodge nitro forums" then search "rear wiper 2008" once in the forums. I'm sure there's rapport on this topic.

Not without modification,

this is true, I have 26" on my Nitro. I had to trim my wheel wells and lift it 2" with the Daystar Lift Kit

Some reasons could be low tire pressure, different size tires, a weak spring, uneven ground, etc.

The Dodge Nitro offered drivers the choice of a 3.7 liter (225 cubic inch) PowerTech V6 engine or a 4.0 liter (241 cubic inch) SOHC V6 engine. In Europe, the Nitro used a 2.8 liter VM Motori I4 diesel engine.

The "bus" is the communication system for the computers on the vehicle. "no bus" means that communication is not happening. It could be a computer, wiring, fuse, ground, etc issue.

YOU don't. The dealer has to. Apparently there is a special tool (not available to public) they use to check it, just another money grab I think.They tell me it has to be connected to a scanner. Probably the aftermarket will come out with something but till then we're at the mercy of the dealer.

Chain

Pull the wiper arm away from the window (it will only come out a few inches). Wrap your left hand around the arm, between the arm and the blade assembly as close to the pivot point as you can get. Grab the blade with your right hand, near the pivot and push away from yourself. The blade will pop right out. It may need a little lube on the pivot like WD40.

You cannot adjust it, you have to replace the lever!

It does not have a MAF.

Tire pressure monitor.

It is part of the pump module in the fuel tank.

It is part of the pump module in the fuel tank.

If the proper precautions are followed, yes.

Key on engine off, press gas pedal to the floor three times, cycle key off and back on.

The 2007 Dodge Nitro has the most common hook-end wiper arms. See sources and related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.