answersLogoWhite

0

🚗

Infiniti

This category covers questions about Infiniti, the luxury division of Nissan Motor Corporation. Infiniti is most well-known for manufacturing performance luxury vehicles.

481 Questions

What is a P0011 trouble code for Infiniti G35?

"A" Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

symptoms
Hard starting, bad idle and possibly stalling issues

caused by
Incorrect camshaft timing
Wiring issues (harness/wiring) in intake timing control valve control solenoid system
Steady oil flow to VCT piston chamber
Faulty timing valve control solenoid (stuck open)

the fix
This code indicated a mechanical issue, electrical troubleshooting wont help so replacement of the VCT or one of it's related components is necessary.

What is the location of the bridge in the current Infiniti tv commercial?

The Multnomah Falls' Benson Bridge, along the Columbia River George in Oregon.

Where is the obd2 port on a infiniti ex35?

The OBD-II port on all vehicles is located under the dash on the driver's side, unless there is a label stating otherwise. Look under the driver's side horizontally - you will see it or the label.

What is the firing order for a 2000 Infiniti G20?

The firing order for a 2000 Infiniti G20, which is equipped with a 2.0L inline-4 engine, is 1-3-4-2. This sequence refers to the order in which the engine's cylinders ignite to ensure smooth operation and balance. It's important to follow this firing order during maintenance or repairs to avoid engine issues.

How do you fix code p1140 Infiniti m45?

Code P1140 on an Infiniti M45 typically indicates an issue with the intake air temperature sensor or its circuit. To fix it, first, inspect the wiring and connectors for any damage or corrosion. If the wiring is intact, test the sensor itself for proper resistance and functionality; replace it if it's faulty. Additionally, clear the code from the engine control unit (ECU) and monitor for reoccurrence.

How do you replace the harmonic balancer on 2000 Infiniti I30?

how to replace harmonic balancer on a 2000 infiniti i30

What kind of battery is used in a remote key for a m35 infiniti?

The remote key for an Infiniti M35 typically uses a CR2032 lithium coin cell battery. This type of battery is common in many key fobs and provides the necessary power for the remote functions. To replace it, you can usually access the battery compartment by gently prying apart the key fob.

Where is the fuse for the factory alarm on a Infiniti j30?

The fuse for the factory alarm on an Infiniti J30 is typically located in the fuse box under the dashboard on the driver's side. You can also check the fuse box in the engine compartment for related fuses. Refer to the owner's manual for a detailed fuse layout and identification. If you're experiencing issues, inspecting the specific fuse for the alarm system is a good starting point.

Why do you have power to the radio CD player but it still does not work in a Infiniti J30 and how do you fix it?

same problemI have this same problem on my infiniti j30.. will be working on it this week so ill get back to you.

(my stereo is not stock)

The Bose system works with amps outside the radio/receiver itself. There are amps on each speaker in the car. I bought three different new radios off Ebay. They were all garbage in the end...(used too).

What I did?

I bought a Kenwood double DIN player. Here's a link:

http://electronics.pricegrabber.com/in-dash-CD-mp3-players/kenwood/p/159/st=filter/popup3%5B%5D=20:521/lo_p=0/hi_p=0/form_keyword=kenwood

I bought the 501. It was a great move. It gets rid of the tape. It has RCA hookups for a woofer, plays MP3's and accepts a 8 gig USB card for music, (generally a little iPod). Sound quality is great. The Kenwood is really nice, but really any stereo will work. Have it be around 50-55 watts per channel. Don't go less than that.

Here's the technical part:

You can still use the Bose speakers, but you need to disconnect and bypass the speaker preamp. Remove the amps. You can sell them on Ebay. Don't cut any wires. Run new wires from the stereo area. Awl a hole thru the boot that houses wires feeding the door's electrical wires. Use a decent gage wire with good insulation covering. Run the speaker cable thru there. You will have to remove the door leather panel liner to get the new wire down to the speaker area. For the rear speakers: run them under the running boards on the driver side to the back. Label the wires to which speaker they will hook up to. You will want to crimp new clamps onto the speaker wires...ones that match the tabs on the speaker.

Use the J30 guide, the one in the trunk, to figure out the electrical diagram wires. Check using a voltmeter to find the hot wires, ground wires and accessory wires. You will not use any of the original speaker wires. An adapter for the antenna will be needed. I bought one on Ebay that was real crap. Goto an audio store. They should have one in stock. (Nissan uses two car antennas. The adapter will combine them into the standard universal plug).

Now you have created a much lower maintenance audio system without losing any sound quality.

How many quarts of oil does a 2006 Infiniti qx56 take?

How many quarts of oil does a 2005 infiniti ax56 take

What country makes Infiniti?

Infinity is the luxury brand of Nissan, which is a Japanese company

How do you change the trunk struts on a 2003 Infiniti m45?

03 m45 Trunk Strut/shock install Burtman Industries.

1. Remove loose items/trunk net/trunk mat(s) from trunk

2. Remove foam inserts (3) and cardboard tire cover

3. Remove the 6 clips using a blunt-edged panel popper

4. You now have access to the canister side of the strut, at the base of

each trunk lid hinge.

5. Remove the rear seat base - there is a round finger tab at the center of

each side. Pull out on the tab and up on the seat base and the side will

release. Make sure the seat belt receivers and seat base hooks (at the rear

of the seat base) clear.

6. Remove the bolt at each corner of the seat back towards the bottom far

right and far left corner. Use a 10mm socket.

7. Pull down the center armrest and carefully pull down the liner behind,

exposing the wire support structure and two 10mm nuts. Remove the two 10mm

nuts.

8. Lift the seat belts around to the back of the seat back so they clear,

then lift the seat back up (off of its mounting rests) and away from the

rear deck. BE CAREFUL when removing this from the car - take it out in one

fell swoop and do not bang it against anything, as the backside had lots of

exposed metal which will scratch whatever it contacts (old installer talking

here).

9. You now have access to the rod end of the struts. In each corner of the

car at the base of the deck, under the big chunks of insulation, you will

find them. Use a broom handle to firmly support the trunk lid, and then use

a pick tool to release the clips on each ball end on the struts. They will

come right off after that.

10. Apply a little thread lock to each end of the new struc, then set the

new rods' ball ends to be the correct length and position by comparing to

the old strut. Install. They will snap on easily.

11. Reinstall the seat and trunk liner parts accordingly.

They work like a charm. Trunk is a little harder to shut, but this is obviously part of the tradeoff with this particular solution.

How fast does an Infiniti m35 get from 0 to 60 miles per hour?

"An Infiniti M35 gets from 0 to 60 miles in approximately 6.1 seconds. In 12.2 seconds, it would be able to reach a speed of approximately 120 miles. More calculation can be made in relation to this, but I believe this should answer your question."

What is the trade in value for an Infiniti M35?

"This totally depends on the year of the Infinity. For a 2006 Infinity M35, providing the mileage is less than seventy thousand and it is good condition could be traded in for $15,000."

Where is the PCV valve located on a 1998 infiniti QX4?

The PCV (Positive Crankcase Ventilation) valve on a 1998 Infiniti QX4 is typically located on the valve cover. You can find it on the driver's side, where it is connected to a rubber hose that leads to the intake manifold. To access it, you may need to remove any surrounding components for better visibility and reach. Always consult the vehicle's service manual for specific instructions and diagrams.