0
To connect Data Terminal Equipment (DTE) to Data Communications Equipment (DCE), a straight-through cable is typically used. This type of cable allows for direct communication between the two devices, with the pinouts configured to match each other correctly. For example, in a common scenario using RS-232 serial connections, a DB-9 or DB-25 cable would be configured with the appropriate wiring to ensure proper signal transmission.
What else can I help you with?
What command is used to verify if a serial nterface is operating as a DTE DCE?
To verify if a serial interface is operating as a Data Terminal Equipment (DTE) or Data Communication Equipment (DCE), you can use the command show controllers in Cisco IOS. This command displays detailed information about the serial interface, including whether it is configured as a DTE or DCE. The output will typically indicate the role of the device, and a DCE interface will often show the clock rate configuration.
What cable would you use to connect two Cisco 2600 series routers?
To connect two Cisco 2600 series routers directly, you would typically use a crossover Ethernet cable if they are connected through their Ethernet interfaces. If connecting through serial interfaces, a serial cable (such as a DTE to DCE cable) would be appropriate. Ensure that the correct interface types are used for the connection type you are employing.
What DTE devices are used on WAN and what DCE devices are used on WAN?
DTE devices in the sense we have PC (Computers), router,Serial Printers, PLC's, Video Cameras, Video Recorders, Video Editors like this we use any of them depending on our requirementDCE devices in the sense hub,bridge,switch,modem etc are dce devices we usei hope it is useful to you........
Why set clock rate in router?
To configure the clock rate for the hardware connections on serial interfaces such as network interface modules (NIMs) and interface processors to an acceptable bit rate, use the clock rate interface configuration command. Use the no form of this command to remove the clock rate if you change the interface from a DCE to a DTE device. Using the no form of this command on a DCE interface sets the clock rate to the hardware-dependent default value.
Why use a clock rate of 64000 for serial interfaces?
When two routers are connected to communicate using a serial cable connection, one end of the router will be using DTE (Data Terminal Equipment) and the other end uses DCE (Data Communication Equipment). In order to communicate effectively with out any delay or to have the same band width, we use 64000 clock rate. This answer is given with the knowledge what I have, please update me if I am wrong. Thank you Syed
What does X25 use as its DTE device?
PAD
What cable do you use between a modem to a cisco router?
External modems are built with a female data communications equipment (DCE) DB-25 port for connection to a controlling device such as a PC or a router. Depending on the model of the router you are connecting to, you will use that type of cable. For details lookup "modem-router configuration" on cisco.com
Can DTE 25 hydraulic oil replace a DTE 26 hydraulic oil operated engine?
DTE 25 and DTE 26 hydraulic oils are both produced by ExxonMobil and are designed for similar applications, but they have different viscosity grades and performance characteristics. DTE 26 typically has a higher viscosity index and better high-temperature performance compared to DTE 25. While short-term use of DTE 25 in place of DTE 26 may not cause immediate issues, it is advisable to adhere to the manufacturer's specifications for optimal performance and to avoid potential long-term damage. Always consult the equipment manual or a lubrication specialist before making any substitutions.
Do you get gas and electricity from dte?
Yes, DTE Energy provides both gas and electricity services to customers in Michigan. They supply natural gas for heating and cooking, as well as electricity for residential and commercial use. If you're a customer in their service area, you likely receive these utilities from DTE. For specific service details or inquiries, it's best to contact DTE directly.
What type of cable should you use to connect PC after connect switch to switch?
To connect a PC to a switch you should use a straight through UTP cable.
When charging a battery, should you use a red or black cable first?
When charging a battery, you should always connect the red cable first before the black cable.
Can you use a usb adapter cable to plug in your bogey man racing wheel?
there should be a certain cable for that
