0
What else can I help you with?
How do you load 32 bit data in 8085 microprocessor?
The 8085 is an 8 bit microprocessor. It cannot directly handle 32 bit data. That said, it is possible to write a routine that can handle 32 bit data, just 8 bits at a time.
What is HL pair in 8085 microprocessor?
HL is a register pair used to store 16 bit of data in 8085 microprocessor.
Why all the 16 address lines are not act as a data lines in 8085 microprocessor?
the 8085 microprocessor is a 8-bit microprocessor and these are bidirectional but the address lines are unidirectional.these address lines are used to address the location of the instruction in memory .these data lines are used to transfer data between processor and peripheral devices. when the address of the instruction will be recognized by the address lines the data will be send to the processor therefore the 16 address lines are not act as a data lines in 8085
What is signal in microprocessor 8085?
In the 8085 microprocessor, a signal refers to an electrical voltage or pulse that conveys information between the microprocessor and other components in the system, such as memory and input/output devices. These signals include control signals, address signals, and data signals, which coordinate operations like data transfer, memory access, and instruction execution. The 8085 uses a combination of these signals to ensure proper communication and functionality within the microprocessor architecture.
How data transfer operation is done in 8085 micro processor?
Data transfer in the 8085 microprocessor can be done with the help of several instructions like the MOV,MVI,OUT and IN . Lets say, we want to move the contents of a register R1 to register R2, then we could use the instruction MOV R2,R1 ; and so on...
What is h-L in the Intel 8085?
HL is a register pair that is used to store 16-bit data in 8085 Microprocessor
How many address bus and deta bus in 8085?
The 8085 microprocessor has a 16-bit address bus and an 8-bit data bus. This means it can address up to 2^16 (or 65,536) memory locations, while it can transfer 8 bits of data at a time. The combination of these buses allows the 8085 to efficiently access and process data from memory.
Why stax h not possible in 8085 microprocessor?
There is no STAX for HL register pair because the data transfer for STAX can be done through XCHG command. For ex: to transfer the data to the memory loaction specified by the HL pair we do as follows: XCHG STAX D for DE pair and BC pair we can directly do it using STAX
What is the function clock out pin in 8085 microprocessor?
In the 8085 microprocessor, the clock out pin (often labeled as CLK OUT) provides a clock signal that can be used to synchronize external devices or circuits. This output clock signal is derived from the internal clock of the microprocessor and operates at a frequency determined by the oscillator connected to the clock input pin. It allows other components in a system to operate in sync with the microprocessor's timing, ensuring proper data transfer and communication.
What is microprocesser 8085?
microprocessor 8085 is basic 8 bit microprocessor by Intel Corp. it has 64Kb memory and 16 address buses and 8 data buses it has 40 pin ic. 8 address and 8 data buses are multiplexed with each other for reducing the total number of pins from the microprocessor 8085 . it require 5MHz clock frequency for operation. only a crystal which connected easily across two pins of microprocessor can provide this clock.
What is function of hold pin in 8085 microprocessor?
The HOLD pin on the 8085 is an external request for control of the bus. Upon receipt of HOLD, the 8085 will complete its current cycle and assert HLDA (HOLD Acknowledge), and then it will float the address, data, and control bus one half clock cycle later. The external hardware is then free to use the bus. When it is done, it releases HOLD, the 8085 releases HLDA, and the 8085 takes control of the bus and continues with the next cycle. HOLD is used by external DMA controllers, such as the 8257, to transfer data to and from memory on behalf of high speed peripherals, without requiring 8085 attention to that data transfer.
Why 8085 microprocessor's AD BUS go into high impedence state before switching as a data data bus?
The 8085 microprocessor's AD bus goes into high impedance state before switching as a data input bus because you don't want two bus drivers driving the bus at the same time. You give the bus time to float between transfer of control, otherwise there will be large power transients at switchover, and you could damage the drivers.
