answersLogoWhite

0

The toilet flange is usually above the floor level. You would have to cut it off the drain pipe and cap it. How you do this depends on what type of pipe the drain is made of. Even if the drain should be below the floor level, you have to seal the drain or sewer gas will come up from the drain.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

Why does toilet over flows when doing laundry?

The laundry waste pipe is fitted to the main drain near the toilet and the main pipe down the line past toilet is partly plugged, forcing the laundry waste up the toilet waste tube. You need to auger the pipe from toilet to outside. If all the piping is in ground you will have to remove toilet from floor to do this properly.


How do I properly install a new toilet flange?

To properly install a new toilet flange, first remove the old flange and clean the area. Place the new flange over the drain pipe and secure it with screws. Make sure it is level and flush with the floor. Finally, connect the toilet to the flange using a wax ring and bolts, then secure the toilet in place.


Are a special flange and washer required in order to install a wallmount toilet in a basement to take advantage of a nearby drain pipe?

You don't have to have one, it just makes it a little easier. As long as the drain is flush with the floor, you can drill into the concrete and us anchors to hold the toilet down. The down side is that they tend to corrode over time and become stuck in the concrete. If you ever have to remove the toilet, they can break and that makes putting the toilet back harder. You can just bolt a mounting ring to the floor and use regular toilet bolts to hold the toilet. These can be easily replaced if needed.


What was the purpose of the toilet?

the purpose of the toilet is to go #2 & #3 and for the waste that comes out to go down the drain and get clean and it does it over and over again


What is the best way to install a toilet flange on top of tile?

To install a toilet flange on top of tile, first ensure the tile is clean and level. Use a wax ring to create a seal between the flange and the toilet drain. Place the flange over the drain and secure it to the floor with screws. Make sure it is level and flush with the tile surface. Finally, attach the toilet to the flange using bolts and nuts.


How do you effectively drain a toilet bowl?

To effectively drain a toilet bowl, start by turning off the water supply valve located behind the toilet. Next, use a plunger to create a seal over the drain hole and push and pull it vigorously to dislodge any clogs. If the plunger doesn't work, try using a toilet auger to break up and remove the blockage. Finally, once the water has drained, turn the water supply back on and flush the toilet to ensure it is draining properly.


How do I install a new toilet flange?

To install a new toilet flange, first remove the old flange and clean the area. Place the new flange over the drain pipe and secure it with screws. Make sure it is level and properly aligned. Finally, connect the toilet to the flange and secure it in place.


Is it possible to install a tub drain above the concrete floor?

You would have to build a platform for the tub to sit on. About 3 inches if you are using a floor drain. There is a trap right after the floor drain so you would not need one at the tub. If possible you could position the tub directly over the floor drain but that would eliminate the floor drain which would be a problem if the basement every flooded.


How do you install a toilet flange correctly?

To install a toilet flange correctly, first remove the old flange and clean the area. Place the new flange over the drain pipe and secure it with screws. Make sure it is level and properly aligned. Finally, connect the toilet to the flange using wax rings and bolts, then secure the toilet in place.


Can you provide a detailed basement floor drain diagram for reference?

I'm unable to provide images or diagrams. However, a basement floor drain typically consists of a grate or cover over a pipe that allows water to flow into the drain. The pipe is connected to a trap that prevents sewer gases from entering the basement. The drain then connects to the main sewer line or a sump pump to remove the water from the basement.


Can you tile over a laminate floor?

Remove the laminate floor first


Can you install a shower stall over a cement floor?

If you have a drain available. You may need to chip some concrete around the drain to install the bottom half of the drain. With that in place, set the shower over it and the top piece screws into the drain to form a seal. You can build a 2x4 frame and raise the shower up enough to run a drain to a sump or a floor drain.