0
What else can I help you with?
How can I fix a stuck tub drain lever?
To fix a stuck tub drain lever, you can try using a lubricant like WD-40 to loosen it. If that doesn't work, you may need to remove the overflow plate and manually adjust the linkage connected to the lever. If the issue persists, it may be best to call a professional plumber for assistance.
How do I go about replacing a tub drain lever?
To replace a tub drain lever, you will need to unscrew the old lever from the drain, remove it, and then install the new lever by screwing it into place. Make sure to follow the manufacturer's instructions and use the appropriate tools for the job.
How does a trip lever tub drain work and what are the common issues associated with it?
A trip lever tub drain works by using a lever to control a stopper inside the drain. When the lever is lifted, the stopper closes to hold water in the tub, and when the lever is lowered, the stopper opens to allow water to drain out. Common issues with trip lever tub drains include the lever becoming loose or disconnected, the stopper getting stuck or not sealing properly, and buildup of hair and debris causing clogs.
How can I troubleshoot and fix a clogged triplever tub drain?
To troubleshoot and fix a clogged trip lever tub drain, you can start by removing the trip lever plate and using a drain snake or plunger to clear the clog. If that doesn't work, you may need to remove the overflow plate and use a drain auger to reach and remove the blockage. Finally, you can try using a mixture of baking soda and vinegar followed by hot water to help break down the clog.
How do you get bottom drain out of bath tub to replace tub?
The piece in the drain is screwed into the drain under the tub It is usually corroded and is not going to unscrew. You can use a sawsall or jig saw to cut the drain in 3 or 4 places around the opening and peel the piece out. You can also disconnect the drain under the tub and just leave it on the tub. There should be access to the back side of the tub. Usually a panel or door in the back of a closet that is in the room beside the bath. If there is no access, you will need to make one so that you can connect the drain to the new tub.
How does a trip lever drain stopper work in a bathtub?
A trip lever drain stopper in a bathtub works by using a lever mechanism to open and close the drain. When the lever is lifted, it pulls a plug out of the drain, allowing water to flow out. When the lever is pushed down, it seals the drain, preventing water from draining out of the tub.
Bath tub over flow lever is stuck?
It is probably just rusted. Take the two bolts out holding it on and pull it up and out of the drain. Nothing will happen when you do this and it will not leak. That way you can spray the backside with some WD40 and free up the lever.
How can I fix a tub drain stopper?
To fix a tub drain stopper, you can try removing any hair or debris clogging it, adjusting the linkage or stopper mechanism, or replacing the stopper if necessary.
How do you tie in a bath tub over flow?
With the two screws supplied with the trip lever waste
What is a right hand drain?
A right-hand drain applies usually to bath-tubs and means the drain is on YOUR RIGHT when you are standing in front of the tub.
How does a trip lever drain work in a bathtub?
A trip lever drain in a bathtub works by using a lever mechanism to open and close the drain. When the lever is lifted, it opens the drain, allowing water to flow out of the tub. When the lever is pushed down, it closes the drain, preventing water from draining out. This mechanism is controlled by a linkage system connected to the drain stopper, which moves up and down to control the flow of water.
What is the purpose of a tub trip lever and how does it function in a bathtub?
The purpose of a tub trip lever is to control the draining of water from a bathtub. It functions by activating a mechanism that opens or closes the bathtub drain, allowing water to either flow out or stay in the tub.
