answersLogoWhite

0

First find the water inlet pipe, normally the one closest to the ground. Before it enters the water heater there should be a valve with a round head or cross head, turn that clockwise till it stops.

Ensure that you aren't turning off the gas supply if your hot water heater is gas fired.

your hot water heater will retain a little pressure in it, so you will need to turn a tap on to relieve the pressure.

From the heater.

Above the hot water (outlet side of the tank) there should be a valve such as a ball / gate and in some rare cases a globe. If the installer was not a professional then you may have to shut the in let valve located on the cold water side of the tank

Turn off the valve and this will cut off the H/W supply to the building.

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How to clean a Rheem tankless water heater effectively?

To clean a Rheem tankless water heater effectively, first turn off the power and water supply. Next, remove the cover and use a soft brush to clean the inside of the unit. Use a vinegar solution to descale the heat exchanger and flush it out with water. Finally, replace the cover and restore power and water supply.


How do I properly flush a Rheem tankless water heater?

To properly flush a Rheem tankless water heater, you will need to turn off the power and water supply to the unit. Connect a hose to the hot and cold water valves, then open the valves to allow water to flow through the unit and flush out any sediment or debris. Repeat this process until the water runs clear. Finally, disconnect the hose and restore power and water supply to the unit.


How can I effectively drain a Rheem water heater?

To effectively drain a Rheem water heater, follow these steps: Turn off the power or gas supply to the water heater. Connect a garden hose to the drain valve at the bottom of the heater. Place the other end of the hose in a drain or outside. Open the drain valve and let the water heater drain completely. Close the drain valve and remove the hose once the water heater is empty. Turn the power or gas supply back on and refill the water heater before turning it back on.


How do I turn on a Rheem water heater?

To turn on a Rheem water heater, locate the gas control valve or the power switch on the unit. For a gas water heater, turn the gas control valve to the "on" position. For an electric water heater, flip the power switch to the "on" position. Wait for the water heater to heat up before using hot water.


How do I properly flush a Rheem tankless water heater to maintain its performance and efficiency?

To properly flush a Rheem tankless water heater for maintenance, follow these steps: Turn off the power and gas supply to the unit. Connect a hose to the flush port on the unit. Open hot and cold water valves to allow water to flow through the unit. Use a pump to circulate a descaling solution through the unit for about 45 minutes. Rinse the unit by flushing it with clean water for about 5 minutes. Disconnect the hose and close all valves. Restore power and gas supply to the unit. Regular flushing helps maintain the performance and efficiency of your Rheem tankless water heater.


How can I turn on the toilet water supply?

To turn on the toilet water supply, locate the shut-off valve usually located behind or near the toilet. Turn the valve in a clockwise direction to open the water supply.


How can I turn off the water supply to the refrigerator?

To turn off the water supply to the refrigerator, locate the shut-off valve usually located behind or near the refrigerator. Turn the valve clockwise to shut off the water supply.


How can I turn off the water supply to the water heater?

To turn off the water supply to the water heater, locate the shut-off valve on the cold water pipe leading to the heater. Turn the valve clockwise to shut off the water flow.


How do you turn off your water heater?

To turn off your water heater, locate the shut-off valve on the cold water supply line leading to the heater. Turn the valve clockwise to shut off the water supply to the heater.


How can I turn off the water supply to the bathtub?

To turn off the water supply to the bathtub, locate the shut-off valve near the tub or in the bathroom. Turn the valve clockwise to close it and stop the water flow.


How can I replace the toilet water supply valve?

To replace the toilet water supply valve, first turn off the water supply to the toilet. Then, disconnect the water supply line from the old valve. Use a wrench to remove the old valve and replace it with a new one. Reconnect the water supply line and turn the water back on to test for leaks.


How do I go about replacing a sink hose?

To replace a sink hose, first turn off the water supply. Disconnect the old hose from the faucet and the water supply line. Install the new hose by connecting it to the faucet and the water supply line. Turn the water supply back on and check for leaks.