answersLogoWhite

0

Water Hammer is best described as the result of instant decrease of volume through the piping system.

For instance: If you have a pipe and valve in the fully open position then the pressure is being quickly released through the valve and very little pressure is put on the pipe system. The water however is traveling through the pipe system at a high velocity to get to the open valve. If that valve is suddenly closed then the pressure within the piping system remains the same but the velocity goes from high to zero instantly. The resulting decrease in velocity will sometimes cause the hammer effect within the pipes.

It is just like having a box on the seat of your car when you are traveling down the freeway. When you are going very fast the box remains in place and is not a nuisance. If you gradually slow down the car the box remains in place and no problems are noted. If however, you stop suddenly, then the box continues to move in a forward direction and hits the dash with a thud.

If your pipes are securely in place within the walls there is usually little or no hammer under normal conditions. if the pressures within the system are high or the pipes are not very secure within the walls and floors of the house, then the water hammer condition can occur.

a simple HAMMER ARRESTOR installed in the correct position or even an EXPANSION TANK placed at the hot water heater is a very in-expensive and reasonable solution. This is much less expensive than removing the drywall at the piping path and re-securing the pipes along the entire path.

Soldering or special tools and skills may be required depending on the type of piping that you have. Your local home improvement store may have everything that you need. Assistance from a plumber may also be required. However, both of these solutions are reasonable for an experienced home owner to do in a couple of hours.

Hope this helps!

Terry

ANSWER:Danced all around it, but never hit the target. A water hammer is when the mass of moving water is stopped by the shutting off of an open valve too quickly, the weight and inertia of the water exceeds the tolerance levels of the pipe and the pipe explodes or bursts outwards from the pressure. For an example. If a fireman opens up a hydrant to put out a fire and 100 gallons are flowing out of the pipe at any given time, if the fireman closes the valve too quickly, the water pressure on the bottom of the hydrant can be as much as 5 thousand gallons in motion at 8.34 lbs per gallon. That's over 40 thousand pounds of pressure on a single valve or section of the water pipe. Most are not made for this tolerance and I have seen up to 160 feet of pipe literally explode from the water hammer that was formed.
User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Does a water expansion tank help with water hammer?

No. Installing an anti-hammer arrestor in water line will take care of water hammer.


How can you stop water pipes from water hammer?

Install a water hammer arrestor (air chamber)


How can I prevent water hammer in my plumbing system when installing a dishwasher by using a water hammer arrestor?

To prevent water hammer in your plumbing system when installing a dishwasher, you can use a water hammer arrestor. This device absorbs the shock caused by sudden water flow changes, reducing the risk of noisy pipes and potential damage. Install the water hammer arrestor near the dishwasher's water supply line to effectively prevent water hammer.


What is the purpose of a water hammer arrestor for a toilet and how does it prevent water hammer in the plumbing system?

A water hammer arrestor for a toilet is used to prevent the banging noise caused by water hammer in the plumbing system. Water hammer occurs when the flow of water is suddenly stopped, causing a shockwave that can damage pipes and fixtures. The water hammer arrestor absorbs the shockwave, reducing the pressure and preventing the noise and potential damage.


What causes a toilet water hammer and how can it be fixed?

A toilet water hammer is caused by a sudden increase in water pressure in the pipes. It can be fixed by installing a water hammer arrestor or adjusting the water pressure regulator.


What is the purpose of a dishwasher water hammer arrestor and how does it prevent water hammer in a dishwasher system?

A dishwasher water hammer arrestor is used to prevent water hammer in a dishwasher system. Water hammer is a sudden increase in water pressure that can occur when water flow is suddenly stopped. The purpose of the water hammer arrestor is to absorb the shock caused by the sudden stoppage of water flow, preventing damage to the dishwasher and plumbing system. It does this by providing a cushion of air or gas that absorbs the pressure surge, reducing the impact and preventing the loud banging noise associated with water hammer.


Why are your pipes banging?

When a valve is closed quickly the flow of water is interupted causing a water hammer. A water hammer arrestor or air chamber can be used to absorb the hammer.


How can a hammer arrestor be installed to prevent water hammer in a dishwasher?

To install a hammer arrestor to prevent water hammer in a dishwasher, you can attach it to the water supply line near the dishwasher. The hammer arrestor acts as a shock absorber, absorbing the pressure spikes that cause water hammer and preventing them from reaching the dishwasher. This helps to protect the dishwasher from potential damage and ensures smooth water flow during operation.


How can I prevent water hammer in my washing machine?

To prevent water hammer in your washing machine, you can install water hammer arrestors or shock absorbers on the water supply lines. These devices help absorb the shock waves caused by the sudden stop of water flow, reducing the likelihood of water hammer. Additionally, ensuring that the water pressure in your plumbing system is not too high can also help prevent water hammer.


Where do you find water hammer?

you can find water hammer In plumbing that is not fastened properly. Water hammer is not an "It" Its the sound made when water is turned off suddenly and the loosely fastened pipes make a banging sound.


How can I prevent water hammer in my whole house with the use of a water hammer arrestor?

To prevent water hammer in your whole house, you can install a water hammer arrestor. This device absorbs the shock waves caused by sudden water flow changes, reducing the likelihood of noisy pipes and potential damage.


How can I prevent water hammer in my plumbing system by installing a water hammer arrestor?

To prevent water hammer in your plumbing system, install a water hammer arrestor. This device absorbs the shock waves caused by sudden water flow changes, reducing the risk of pipes banging and potential damage.