answersLogoWhite

0

The key word is "drain", meaning it works by gravity, so a drain value should be at the lowest point in the system. Typically there is one just past the meter.

If a lawn irrigation system is a branch of the main system it should have its' own drain valve for winterizing it.

You can purchase stop valves (or shutoff valves) with built-in drain or bleeder valves.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

How many valves does the 2012 Subaru Forester have?

The EJ25 series engine fitted to the 2012 Subaru Forester has 16 valves.


Replaced thermostat and still no heat in my VW Golf?

This is a common complaint with mk2 Golfs, most of which were fitted with a heater matrix bypass valves to prevent the heater matrix from bursting under certain conditions. These bypass valves can fail, cutting off supply to the heater matrix resulting in no heat. Either replace the valves or remove them and fit a heater matrix from a mk3 Golf. These are stronger units and don't require bypass valves.


How to unhook a washer from the water supply and drainage system?

To unhook a washer from the water supply and drainage system, first turn off the water supply valves. Then, disconnect the hoses from the water supply and drainage pipes. Be sure to have a bucket ready to catch any excess water. Finally, carefully move the washer away from the connections.


What should I do if my Rain Bird sprinkler system is experiencing low pressure?

If your Rain Bird sprinkler system is experiencing low pressure, you should check for any clogs or leaks in the system, ensure that the water supply is sufficient and that the valves are fully open, and consider adjusting the pressure regulator if necessary. If the issue persists, you may need to consult a professional for further assistance.


How do you re-pressurise your water system?

To re-pressurise your water system, first, turn off the water supply and locate the pressure gauge on your system. If the pressure is below the recommended level (usually between 1-1.5 bar), open the filling loop valves to allow water into the system until the desired pressure is reached. Once achieved, close the valves and check for any leaks. Finally, turn the water supply back on and ensure the system is functioning properly.


Got 16v cam belt snapped had new valves fitted now a taping witch goes after 10 mins what can you do?

were the hydraulic cam followers changed with the valves if not, that is the problem.


Why non return valve is fitted on the suction side of the multistage Grundfos pumps?

I'm not famiar with the Grundfos valves specifically, but non-return valves are usually fitted to the suction side of pumps to prevent the pump from losing it's prime when it is stopped (by draining back through the inlet).


When evacuating a refrigeration system that has solenoid valveswhat special procedure must be followed?

When evacuating a refrigeration system with solenoid valves, it is important to ensure that the solenoid valves are in the correct position to prevent any refrigerant from being trapped in the system. This usually means that the valves should be in the open position during evacuation. Additionally, ensure that the suction and discharge service valves are closed to avoid introducing air or moisture into the system. Always follow the manufacturer's guidelines for specific procedures related to the solenoid valves in the system.


Why non-return valve are fitted to bilge pipes in watertight?

Non-return valves are fitted to bilge pipes in watertight compartments to prevent the backflow of water into the bilge system. This feature ensures that any water pumped out does not re-enter the compartment, which could compromise the vessel's stability and safety. Additionally, by maintaining a one-way flow, non-return valves help to keep the bilge area dry and reduce the risk of flooding. Overall, these valves are crucial for effective bilge management and overall vessel integrity.


How can I connect a washing machine to the water supply and drainage system?

To connect a washing machine to the water supply and drainage system, first locate the water supply valves near the washing machine. Connect the hot and cold water hoses to the corresponding valves, ensuring they are securely tightened. Next, connect the drainage hose to a standpipe or a dedicated drainage pipe, making sure it is not kinked or blocked. Test the connections by running a short cycle to check for leaks.


How a deluge valve works?

Deluge valves are hydraulically operated differential type valves used to control water supply to a deluge system. Deluge systems use open sprinklers or nozzles. Trim sets are used to control the operation of the valve.


How deluge valve working?

Deluge valves are hydraulically operated differential type valves used to control water supply to a deluge system. Deluge systems use open sprinklers or nozzles. Trim sets are used to control the operation of the valve.