0
If you mean that a gas hot water heater (HWH) has the flame go out (located beneath the HWH tank.) Then this is the normal operation whenever the temperature reaches the set point. You can regulate this temperature by adjusting the control, on the HWH. (hint: Be careful when raising the temperature, increase it slowly over a few days as the shower temp. may surprise someone in your home.) If it continues to shut off too frequently, you may have a gas or HWH regulator related problem, in that case call a professional.
This explanation does not apply to electric or oil fired HWH's.
What else can I help you with?
How can I effectively remove sediment from my water heater?
To effectively remove sediment from your water heater, you can follow these steps: Turn off the power or gas supply to the water heater. Allow the water heater to cool down. Connect a garden hose to the drain valve at the bottom of the water heater. Open the drain valve and let the water and sediment drain out into a bucket or drain. Flush the water heater by turning on the cold water supply for a few minutes to help remove remaining sediment. Close the drain valve and refill the water heater. Turn the power or gas supply back on. It is recommended to perform this maintenance task annually to keep your water heater running efficiently.
Why does the pilot light on my water heater keep going out?
The pilot light on your water heater may keep going out due to a variety of reasons, such as a dirty or damaged thermocouple, a faulty gas valve, insufficient gas supply, or a draft in the area where the water heater is located. It is important to have a professional inspect and repair the water heater to ensure safe and efficient operation.
Would you be able to find a shut off valve to keep water from entering heater coil?
There is no shut off valve. But you can by pass the heater core by disconnecting the 2 hoses going to the heater core. And connecting them together. The only problem with this is that you won't have any heat in the winter.
How can I effectively flush out a water heater to maintain its performance and efficiency?
To effectively flush out a water heater and maintain its performance and efficiency, follow these steps: Turn off the power or gas supply to the heater, connect a hose to the drain valve at the bottom of the tank, open the valve to drain the water, flush out any sediment by letting water run through the tank, close the valve, refill the tank, and turn the power or gas supply back on. Repeat this process annually to keep your water heater working well.
How to Keep Your Water Heater Clean?
By Andreina Urdaneta A clean water heater will heat and maintain water better and last longer. Once a year, flush your water heater, and in extreme hard water areas, at least twice a year. If you feel up to the challenge, here are some tips to help you in a basic cleaning. 1 Turn the water heater and the cold water supply to the water heater off. 2 Hook a high-quality garden hose to the drain valve, and place the other end in an area where hot water will not cause damage. 5. Open the drain valve. 6. Disconnect the cold water pipe on the top of the water heater. This step will let air into the water heater so it will drain. When the water heater is empty, close the drain. 8. Pour tile cleaner into the cold water, leave for a couple of hours and drain the detergent out of the tank. 10. Reconnect the cold water supply to the water heater. Open the cold water valve and let the water heater flush for a couple minutes. 12. Close the drain valve and open the hot water faucet nearest to the tank, and let the water heater fill. 13. When water starts to come out of that faucet, reopen the drain and let the water heater continue to rinse. After all the air is out of the water heater, turn it back on. Take care of your water heater, and it will take care of you. If you keep ignoring the task, your water heater may just leave you in the cold.
Why does my hot water heater pressure relief valve keep opening?
Your hot water heater pressure relief valve may keep opening because there is excessive pressure or temperature in the tank, which can be caused by issues such as a faulty thermostat, high water pressure, or a malfunctioning heating element. It is important to have a professional inspect and repair the problem to prevent potential damage or safety hazards.
Why does my hot water heater overflow keep discharging water?
Your hot water heater overflow may be discharging water because of a malfunction in the pressure relief valve. This valve is designed to release excess pressure to prevent the tank from bursting. If it is continuously discharging water, it could indicate that the valve is faulty or that the pressure in the tank is too high. It is important to have a professional inspect and repair the issue to prevent any potential damage or safety hazards.
How does a heater control valve work in a car?
A heater control valve is simply a water valve which allows more or less water to circulate through the heater core, depending on how much the valve is opened. When the engine warms up it heats coolant (mostly water) in the water jacket of the engine. To keep the engine from overheating, the water pump circulates water through the radiator once the engine temperature reaches the set-point of the thermostat. When it's cold outside the engine STILL reaches a temperature that allows you to make use of the engine heat when you open the water valve of the heater. Heater control valves take many forms but basically they all do the same thing; they open to allow heated engine coolant to circulate through the heater core or they close to stop the coolant from flowing. Heater control valves can be manual (cable controlled or even lever controlled), vacuum (which allows the engine vacuum to control the position of the heater control valve based on where you set the control knob) or electrical which allows for greater flexibility and even allows the auto manufacturer to connect the heater controls to a computer or other electronic control device.
What happens to the water heater when the water main is turned off?
It will keep the water hot as long as the electricity or gas is on. If it's going to be off more than a day, turn the breaker or gas valve off.
What does the Heater and rad hoses do?
rad hoses route coolant to the engine to maintain operating temperature (to keep engine from overheating). Heater hoses supply the heater core (inside most vehicles) with hot water, when heater/ac temperature control knob is turned toward hot, to heat the interior of the vehicle by opening and closing a water flow control valve allowing water to enter the heater core for heat. =;)
Why does my water heater pilot keep turning off?
There are several possible reasons why your water heater pilot keeps turning off. It could be due to a faulty thermocouple, a dirty pilot light, a gas supply issue, or a problem with the gas control valve. It is recommended to have a professional inspect and repair your water heater to determine the exact cause of the issue.
Can a water heater freeze and what steps can be taken to prevent it from happening?
Yes, a water heater can freeze if exposed to extremely low temperatures. To prevent this, you can insulate the water heater and pipes, keep the area around the water heater warm, and allow a small amount of water to drip from a faucet to keep water flowing.
