0
What else can I help you with?
What is the name of peak and claw of crow?
The peak of a crow is commonly referred to as its "beak." The claws of a crow are typically called "talons." Crows, like other birds, use their beaks for foraging and eating, while their talons help them grasp and manipulate objects, as well as perch securely.
What are the peak and off peak times for mobile phones?
It depends on your carrier. Some start nights at 9 PM, others at 7 PM.
When the peak output voltage is 100 V the PIV for each diode in a center-tapped full-wave rectifier is (neglecting the diode drop)?
In a center-tapped full-wave rectifier, the peak inverse voltage (PIV) for each diode is equal to the peak output voltage. Therefore, when the peak output voltage is 100 V, the PIV for each diode is also 100 V. This is because each diode must withstand the full peak voltage when it is reverse-biased. Thus, each diode in this configuration experiences a PIV of 100 V.
Is 12 volts peak to peak the same as 12 volts ac?
No. 12 volts peak to peak would be 6 in the positive polarity and 6 negative polarity. Simply saying 12 volts AC would be 12 volts in each polarity or 24 volts peak to peak
What is PIV in electronics?
The Peak inverse voltage (PIV) equals the peak value of the input voltage, and the diode must be capable of withstanding this amount of repetition reverse voltage. For the diode in figure, the maximum value of reverse voltage, designated as PIV, occurs at peak of each positive alternation of the input voltage when the diode is forward biased.Peak Inverse Voltage at Positive Half CycleThe Peak Inverse Voltage (PIV) occurs at the peak of each half-cycle of the input voltage when the diode is forward biased . In this circuit, the PIV occurs at the peak of each positive half cycle.
How are Baghdad and golden age linked with each other?
Baghdad was at its highest peak at different times, Golden age means "A city at its highest peak
What is the sexual peak of women?
Women have their sexual peak in their 30's.It depends on the iduvidual, some lose interst at an early age while others are still dreaming in their 70's
What is 'non-coincident peak demand' in an electrical system?
Non-Coincident Peak (NCP) is the individual or actual peak demands of each load in an electrical system oftentimes occurring at different hours of the day. It does not necessarily fall during system peak. (This is what i understood about NCP...I gladly welcome corrections)
What is 'non coincident peak demand' in an electrical system?
Non-Coincident Peak (NCP) is the individual or actual peak demands of each load in an electrical system oftentimes occurring at different hours of the day. It does not necessarily fall during system peak. (This is what i understood about NCP...I gladly welcome corrections)
What do concentric circles on topographic maps indicate?
Concentric circles on topographic maps indicate the presence of a hill or peak, with each circle representing a different elevation level. The closer the circles are to each other, the steeper the slope of the hill or peak.
A generating station is to supply six regions of load whose peak loads are 15000kw ,8000kw?
To determine how much power is needed to fulfill each region's requirement, we first need to know the total peak load of all six regions combined. Total peak load = 15000 kW + 8000 kW + (four more regions' peak loads) Assuming the peak loads of the other four regions are x1, x2, x3, and x4, we can write: Total peak load = 15000 + 8000 + x1 + x2 + x3 + x4 We do not have information about the other four regions, so let's assume they each have a peak load of 10,000 kW: Total peak load = 15000 + 8000 + 10000 + 10000 + 10000 + 10000 = 58000 kW Therefore, the generating station needs to be able to supply a peak power of 58,000 kW to meet the combined peak load of all six regions. To determine how much power is needed to fulfill each region's requirement, we need to divide the total peak load by the number of regions: Power needed per region = Total peak load / Number of regions = 58000 kW / 6 = 9666.67 kW Therefore, each region needs a peak power of approximately 9666.67 kW to fulfill its requirement.
Where is the ridge on a roof?
The highest point, the peak of each gable or hip.
