To properly spool fishing line onto a reel, first, attach the reel to a rod. Then, thread the line through the rod's guides and tie it securely to the reel spool. Close the bail or line roller, and start winding the line onto the spool evenly and tightly. Make sure to keep tension on the line to prevent tangles. Fill the spool to about 1/8 inch from the rim, and trim any excess line.
To properly thread fishing line onto a fishing reel, start by tying the line to the reel spool using an arbor knot. Then, close the bail and start winding the line onto the spool evenly and tightly. Make sure to keep tension on the line as you wind it to prevent tangles. Once the spool is filled to the desired level, cut the line and secure it with a knot or tape.
To properly string fishing line onto a fishing reel, follow these steps: Open the bail on the reel and thread the line through the rod guides. Tie the line to the spool using an arbor knot. Close the bail and start reeling the line onto the spool, making sure it lays evenly. Fill the spool to about 1/8 inch from the rim. Trim any excess line and secure the end with a knot or tape.
To properly load fishing line onto a reel, start by threading the line through the rod guides and tying it securely to the reel spool. Then, close the bail or line roller and begin winding the line onto the spool evenly and tightly. Make sure to keep tension on the line as you wind it to prevent tangles. Fill the spool to about 1/8 inch from the edge, leaving some room for casting. Cut the line and secure it to the spool.
To put new fishing line on a closed reel, follow these steps: Open the bail on the reel. Thread the new line through the rod guides. Tie the line to the spool using an arbor knot. Close the bail and start reeling the line onto the spool. Fill the spool to the desired capacity, leaving a small gap at the edge. Trim any excess line and secure it in place.
To properly restring a Ryobi weed eater, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet. Insert one end of the line into the hole in the spool and wind it in the direction indicated on the spool until it is full. Secure the line in the notches on the spool and reassemble the spool onto the trimmer head. Cut the line to the desired length and you're ready to trim.
Try these sites:# http://fishing.about.com/od/basicfishinginstruction/a/spooling_spin.htm# http://www.wikihow.com/Keep-a-Spinning-Reel-Line-Trouble-Free# http://www.ehow.com/how_13894_load-fly-fishing.html
To replace fishing line on your reel, follow these steps: Remove the old line by unwinding it from the reel. Clean the reel and spool to remove any dirt or debris. Attach the new line to the reel by tying a secure knot. Wind the new line onto the reel, making sure it is evenly distributed. Trim any excess line and test the reel to ensure it is working properly.
To put on a fishing hook properly, first tie a fishing knot to the end of your fishing line. Then, slide the eye of the hook onto the knot and pull it tight. Make sure the hook is securely attached to the line before baiting it and casting your line into the water.
To change the line on a Ryobi weed eater, first, remove the spool cover and take out the old line. Cut a new line to the correct length and insert it into the spool. Wind the line evenly and securely onto the spool, then reassemble the spool cover.
To reload the line on your Ryobi string trimmer, first remove the spool from the trimmer head. Cut a length of new trimmer line, usually around 10 feet, and insert one end into the spool's center hole. Wind the line evenly and tightly around the spool in the direction indicated on the spool. Leave a few inches of line unwound, then thread the line through the trimmer head's eyelet. Reassemble the spool onto the trimmer head, ensuring the line feeds through the head properly.
First release the spool from the reel. Then take a length of string and tie it to the spool use a small knot keep it tidy.You then wind the string onto the spool in a clockwise direction until it covers approx 1/8 of the capacity of the spool.You then attach the nylon fishing line or braid,to the string with a small tidy knot and try hiding the knot on the outer edge of the spool.You then lift up the bail arm of the reel and refit the spool and close the bail arm.You would then load your line onto the reel until 1-3mm from the top of the spool, Be sure to wind the lines reasonably tightly.
To replace the line on a Ryobi Expand-It weed trimmer, first, remove the spool cover and take out the old line. Cut a new piece of line to the appropriate length and feed it through the holes on the spool. Wind the line evenly and securely onto the spool, then replace the spool cover.