0
What else can I help you with?
What is the formula for a 45 degree lateral on 6 inch weld pipe?
formula for a 6" 45 degree lateral onto a 6" main
How do you calculate a 45 degree elbow take off?
To calculate a 45-degree elbow takeoff, you need to consider the diameter of the pipe and the flow rate. Typically, you can use the formula for an elbow fitting's pressure loss, which is based on the flow velocity and the elbow's characteristics. Additionally, you may need to refer to manufacturer data or standards that provide specific loss coefficients for a 45-degree elbow to ensure accurate pressure drop calculations in your system.
When can take the 1.4142 formula to 45 degree?
cuando se desea cuadrar un angula de 90 grados , no necesariamente usando el teorema de pitagoras.
What fraction is 45 degree?
1/8 of a circle
What part of the Earth's surface is represented at 0 45 and 90 degree angles?
0=45 degrees?
What Formula for long radius 45 degree elbow?
1.414. x offset- Straight of 45's
Calculate 45 degree offset when the travel is known?
A 45 degree offset has a travel of 200mm. calculate the rise of the offset.
What is oblique offset in surveying?
offset that are not situated 90 degree rather that are situated in any angle like 60 degree or 45 degree
What is the offset in a 45 degree pipe run?
The offset in a 45-degree pipe run refers to the vertical or horizontal distance a pipe is shifted from its original line due to the angled connection. In practical terms, when a pipe is installed at a 45-degree angle, it creates a diagonal path that results in both vertical and horizontal displacement. The actual offset can be calculated using trigonometric principles based on the length of the pipe run and the angle. Typically, for a 45-degree angle, the horizontal and vertical offsets are equal.
What is the formula for a 45 degree lateral on 6 inch weld pipe?
formula for a 6" 45 degree lateral onto a 6" main
What is pipefitting formula for 30 degree offset?
To calculate a 30-degree offset in pipefitting, you can use the formula: Offset = Rise / Run. For a 30-degree offset, the rise is typically equal to the run multiplied by the tangent of 30 degrees (tan 30° ≈ 0.577). Therefore, if you have a specific run measurement, you can determine the rise by multiplying the run by 0.577. This allows you to accurately position the pipes at the desired angle.
What is pipefitting formula for 45 degree offset?
whatever the offset is times it by 1.414 and this will give you your travel then just take off the centres of the 45's and you have your cut length....for instance if the offset is 12 inchs you multiply it by 1.414 you come up with 16.968..meaning 1 foot 4 inchs 15/16 just thought alittle clarity might help if the person was new in trade.
What multiplier would be used for EMT conduit to make a 45 degree offset bead?
The multiplier for a 45 degree bend is 1.4142 (rounded off to 1.4) times the height of the offset. All offset multipliers are the cosecant of the angle. (inverse of the sine of the angle). However, 45 degree offsets are very difficult to pull wire through and should be avoided. Always bend your EMT to the shallowest angle you can for the distance you have to do it in.
What is the take off formula off 45 degree elbow pipe?
The take off formula of a 45 degree elbow pipe, will depend on what the pipe is on. Sometimes a 45 degree pipe will need a 90 degree right angle turn to come off.
How do you calculate a 22.5 degree offset?
i want to make 22.5 degree offset so how can i offset of 22.5make ritgh
If the formula for 45 degree is 1.4142 what is the formula for 60 degree?
If it's a ratio problem, then 45 is to 1.4142 as 60 is to x 45/1.4142 = 60/x 45x = 84.852 x = 1.8856 Otherwise, there isn't enough info to answer
What is the formula 45 degree elbow?
15.875 x pipe size=
