0
What else can I help you with?
Question poised to me by contractor. What pitch is your roof My answer was that it rises at a 25 degree angle. What is the pitch in his terms?
If I remember right it should be between a 5 and 6 pitch. Between a 5/12 pitch and 6/12 pitch. If it was 27.5 degrees it would be a 6/12 pitch. Enter in "roof pitch" in the Google bar and several sites will come up where you can calculate pitch. The 12 means 12 inches. So that it would be aproximitely 6 inches rise to 12 inches of run. Hope this helps and I hope I remember my roof pitch angles. It has been a few years since I have done it.
Roof 50 foot by 100 foot with a 412 pitch what is the formula?
a 100 foot run with a 50 foot rise would give you a 6/12 pitch
What does a 1 on 2 pitch mean in terms of a roof?
In general, talking about roof pitch, I have never heard or read about this term being used. Roof pitch is measured when you start at the leading edge of a roof and measure towards the center of the house too 12 feet. Pitch is measured from a imaginary parallel level line at the 12 foot mark, how many feet high the roof is at 12 feet is the pitch of a roof. If your roof is at 4 feet high at the 12 foot mark then the phrase would be- a 4/12 pitch.
What is pitch of a filet weld?
Pitch is center to center spacing of an intermittent weld.
What is the minimum pitch of a single pitch roof?
1x12 for metal or rolled roofing, 3x12 for shingles.
What should the pitch of your patio cover be if the patio is 20ft by 13ft?
That depends on the roof material. Metal can be as low a 1/12. Fibergglass shingles should be at least 3/12.
If my patio cover roof has a pitch of quarter inch per foot can you use composition shingles?
3 inch per foot is usually the lowest pitch for shingles. For only 1/4 inch slope, rolled roofing should be used.
Should a patio of pavers pitch away from or towards a pool?
Pavers should drain away from your pool.
What should the pitch of your patio cover be if the patio is 20ft by 20ft?
A 1/4" per foot is standard, therefore in twenty feet the furthest point would be 5" below the high point. You can make it flatter (3 or 4 inch drop) but it would require greater perfection in concrete placement, perhaps beyond reason.
Cover drive in cricket?
A shot played by the batsman through the cover area of the pitch ( 35 degrees- 70 degrees)
Can you fix the pitch on a concrete patio if its to much?
If it is a free floating slab, not tied to the house, you could probably have it mud jacked on the low side depending on what is beside it,
How would you change the pitch and loudness of the recorder?
To change the pitch of a recorder, you can cover or uncover the finger holes to alter the length of the air column inside the instrument. The more holes covered, the lower the pitch. To change the loudness, you can blow harder or softer into the instrument, controlling the intensity of the sound produced.
How many A4 sheets of paper to cover a football pitch?
To cover a standard football pitch, which measures approximately 7,140 square meters, you would need around 71,400 A4 sheets of paper. An A4 sheet measures about 0.062 square meters, so dividing the total area of the pitch by the area of one A4 sheet gives the total number required. This is a rough estimate, as the actual number may vary slightly based on the exact dimensions of the pitch and the layout of the sheets.
What would happen to the sound produced by a stretched string if you increased it's tautness?
The pitch would increase, getting higher.
How many times around a football pitch is 1 km?
A standard football pitch is approximately 100 meters long and 64 meters wide. The perimeter of a football pitch is about 328 meters. Therefore, to cover 1 kilometer (1,000 meters), you would need to run around the pitch approximately 3 times (1,000 meters divided by 328 meters is roughly 3.05).
How were boats made in the olden days?
bananasSome cultures would hollow out and shape a whole tree trunk. Many other cultures would secure wooden boards to a wooden frame then cover the hull with pitch, a natural tar.
How do you change the pitch on a harp?
If you would want a high pitch you would need to pluck the strings hard and if you would like a low pitch you would need to pluck it lightly for a harp!
