answersLogoWhite

0

Patching a hole in a pool wall where the skimmer is located can be challenging, as the skimmer is crucial for water circulation and filtration. It's essential to use a suitable repair material, such as epoxy or a specialized pool patch, ensuring a watertight seal. However, if the damage is extensive or affects the structural integrity, it's best to consult a professional to assess and repair the skimmer properly. Proper installation and sealing are vital to prevent leaks and ensure the skimmer functions effectively.

User Avatar

AnswerBot

2mo ago

What else can I help you with?

Related Questions

How do you repair a hole near the bottom of an aluminum wall of a Poseidon above ground oval pool?

Buy a pool patch


How do you repair a hole in a pool wall without removing the liner?

There are several pool patch kits available at your local pool dealer...if the hole is not too big than this should work. It works under water.


Can you install a through the wall skimmer in a soft sided pool?

yes


How to patch a hole in a wall?

To patch a hole in a wall, you will need to clean the area around the hole, cut a patch of drywall to fit the hole, apply joint compound to the edges of the hole, place the patch over the hole, and then smooth out the joint compound. Sand the area once it's dry, and then paint over it to match the rest of the wall.


Is there any kind of repair kit for a rusted pool wall around your through wall skimmer?

If this is an above ground pool you could just pull the old skimmer out cut the rusted section of metal out hit it with some rust converter, replace the section where there is no metal with a new metal forget about the old skimmer setup and replace it with a "floating pool skimmer" they do a better job any way.


How can I effectively use a wall repair patch to fix a hole in my wall?

To effectively use a wall repair patch to fix a hole in your wall, first clean the area around the hole. Cut the patch to fit the hole, apply a layer of joint compound to the wall, place the patch over the hole, and cover it with more joint compound. Smooth the compound, let it dry, sand it down, and paint over it for a seamless finish.


Can you replace the skimmer without replacing the liner?

Yes you can. Drop the waterline in the pool below skimmer level, dig a whole around your skimmer to gain access. Unscrew the skimmer faceplate and remove it as well the old gasket. You also have to remove the second gasket between liner and wall. Detach the pipe(s) from the skimmer. Now install the new skimmer by attaching the pipe(s) to the skimmer put new gaskets in place screw the faceplate back on and you're done. Don't forget to fill your hole again and put water back in the pool to the appropriate level. ;-) Jens Poseidon Pool Services, Dunrobin, ON


Can you replace a skimmer without replacing the liner?

There are several forums that describe how to replace a skimmer. Assuming you have a concrete walled pool, it will require pouring of cement and doweling epoxy coated metal rods into the existing wall. If this isn't done it will crack and cause additional skimmer leak problems. Assuming the above, and even with an exact replacement, it would be impractical to try and save the liner, and to assume that cutouts and holes will line up etc. However, if it is a budget challenge and you have no choice, a less cosmetically appealing attempt could be to apply a patch over the existing cutout. This would require obtaining a section of pool liner (such as a 16 x 24 inch piece), vinyl pool patch cement,and, of course, creating a fairly large patch that extends to the upper lip of the liner and several inches around the perimeter of the skimmer. (This patch will never match your existing liner ...thus the reason it would be less appealing.) After lowering your pool water level, remove the skimmer bezel (on the water side of the pool liner) and, leaving the upper lip of the liner locked in it's channel, apply the patch in place. (This you would do before attempting any skimmer repair.) Let the patch dry for a day, make certain it looks well sealed, and then pull the liner out of the channel sufficiently enough to conduct the skimmer replacement work. After the new skimmer is in place, carefully reinstall the liner in the channel. Install the new bezel and screws and cut out the skimmer hole. When installing the liner section back in the channel, keep a pot of very warm water nearby. You will likely need to pour it on that section of liner to allow it to strectch into place. Bob


Where do you attach the vacuum hose to vacuum the pool?

Attach the hose to the side skimmer basket with a special plastic adaptor that fits in your size skimmer. Types of skimmers: Brands: Purex, Anthony, American Products, Pentair, Hayward are major names. Hum, not inside the skimmer basket but under it. There you will find either a disc type object much like a flying saucer. Then under that there will be 2 holes. The one, if you are looking down into the skimmer from the deck side of the pool, to back side of the skimmer - 0 0 < that one - closest to you is the suction part of the skimmer. Your hose is pushed into this hole after filling the hose with water. The "adapter" is another type skimmer as stated above that you can rotate to the left or right to achieve optimum skimmer suction. With a single hole skimmer - that hole is the suction for the vac. You just have to plug the second skimmer if you have one. Still, there is another with a hole in the side wall of the skimmer near the bottom of the skimmer. This is also the vac hole. With it you plug yoyr vac into it and then close a valve that controls the main drain. You have to remember when you are finished vacing pool you then open the main drain valve. The latter one is a quite old system made by or used by Anthony Pools. k


How can I effectively patch drywall to repair a hole or damage in my wall?

To effectively patch drywall to repair a hole or damage in your wall, you will need to clean the area, cut a patch to fit the hole, secure the patch in place with drywall screws, apply joint compound to cover the patch, sand the area smooth, and then paint over the repaired area to match the rest of the wall.


How can I effectively patch a hole in a plaster wall?

To effectively patch a hole in a plaster wall, you will need to clean the area around the hole, apply a patching compound, smooth it out, and then sand and paint over the patched area to match the rest of the wall.


When you replace the liner on your above ground pool can you cover up the holes for the return and skimmer and put the holes somewhere else on the pool wall?

Yes you can, it will void your warranty on the pool wall, but it can be done. Make a template from the existing skimmer hole so you can cut in the new hole. After the liner is removed simply duct tape a piece of galvanized sheet metal, paint the cut edges as to prevent rust, ofer the holes for the skimmer and return. Make sure the sheet metal is at least 6"-10" past the existing holes. The duct tape only holds the metal in place and protects the liner from sharp edges.