answersLogoWhite

0

We have the metal type and our drain valve is located right near the bottom very close to the area where the higher filter port sits. There is an outside and an inside cap, so you will have to actually get into the pool to remove the inner cap.... something we didn't bargain for when taking ours down. Hope that helps.

User Avatar

Wiki User

16y ago

What else can I help you with?

Related Questions

Can leaks in intex pools be repaired?

Yes, leaks in Intex pools can be repaired using various methods, depending on the size and location of the leak. Small punctures or holes can often be fixed with a vinyl patch kit specifically designed for inflatable pools. For larger leaks or structural issues, it may be necessary to drain the pool and apply a more comprehensive repair solution. It's important to identify the source of the leak and address it promptly to prevent further damage.


What is PVC in plumbing?

Poly vinyl chloride. -Very common for irrigation and drain pipes.


PCV valve Location acura TL?

On a 2nd generation 1999 the PCV valve is located on rear valve cover (facing firewall) and the driver side under a little vinyl/rubber shroud. It may help to remove the rear bolts on the plastic engine cover to gain more access.


How can you repair a severe leak from the molded plastic exit valve on an above ground plastic swimming pool?

Walgreens sells a product for vinyl repair that works very well when used as directed. it is called POWER POXY. The valve needs to be replaced. Do not attempt to repair the valve. The patch will not last and could be dangerous people if it were to separate into pieces. If the valve were to break while in operation or while the pump was running the resulting break could drain the pool.


How to change Toyota Paseo transmission fluid?

Assuming it is a manual transmission: Remove the lower drain plug on the transaxle body and allow all existing fluid to drain completely. Replace the drain plug and remove the fill valve, located higher on the transaxle body. You'll need a pump assembly and vinyl hose to pump the transmission fluid into the transaxle. Any good auto parts store sells these plastic pumps at nominal prices. The pump assembly screws onto the top of the transmission fluid bottle. Pump the new oil through the vinyl hose into the transaxle until it begins to come back out of the fill hole. Then screw the fill plug back in. It a very easy process once you've found the drain and fill plugs and get yourself situated underneath the transaxle.


How do you drain water out of a pool?

If it is a vinyl liner pool you have to use a submersible pump. You can get a small one for right at $100.


How do you keep water from getting behind the liner and moving it out of place when you have a lot of rain?

We have a vinyl lined in-ground pool and in the winter, when we have some torrential rains, I go out & open up the backwash valve on our filter & drain the pool until it's at a level where the water won't get behind the liner. Or else I remove the bleed valve located at the top of the filter. Both ways work well. I don't worry too much about recharging the filter with DE filter powder until the rainy season is over. So, depending on where you're located, you may have to recharge your filter after doing this.


Where is Mannington Vinyl located?

Mannington Vinyl is located at six locations: Alabama, Georgia, New Jersey, and North Carolina, California, and Florida. The company offers a variety of options for home and commercial flooring.


How do you drain an in ground vinyl liner pool?

The best way to empty a pool is with a portable water pump, they have small pumps that can pass 2280 gallons a hour (small 43cc 2 cycle motor and pump). You can buy one or they have them to rent at hardware stores and tool rental places. OR Use the pool's existing pump. Set the spider valve to waste and the suction to pull only from the main drain.


Can you paint a intex pool on the outside?

Yes, you can paint the outside of an Intex pool, but it's important to use a paint designed for plastic or vinyl surfaces to ensure proper adhesion and durability. Before painting, clean the surface thoroughly and allow it to dry completely. Additionally, consider applying a primer specifically formulated for plastic materials to enhance the paint's longevity. Always check the manufacturer's guidelines for any specific recommendations regarding painting the pool.


Where is the Vinyl Cafe located?

The Vinyl Cafe is actually a radio program broadcast on the CBC from Canada. They are also on public radio stations in the United States and on Sirius Radio.


I have an Intex vinyl pool that is 18 foot by 4 foot I am looking for a heater that will work with this pool that is available and usable in the US anyone know where to get one?

Do you have a supply of gas running to the equipment pad? What about electricity for the heater - is there ample electricity available for a direct hook up to the time clock?