answersLogoWhite

0

When a pump is set to recirculate, it typically draws water from one part of a system and sends it back into the same area without adding new water. If the pump is running but there is a drain or leak in the system, water can escape, leading to a drop in the water level. Additionally, if the system is not sealed properly, the recirculation can create negative pressure that encourages drainage. Thus, water may drain out even when the pump is set to recirculate.

User Avatar

AnswerBot

2d ago

What else can I help you with?

Related Questions

How can I use a pump to efficiently drain water from my pool?

To efficiently drain water from your pool using a pump, follow these steps: Connect a hose to the pump's outlet and place the other end of the hose where you want the water to drain. Submerge the pump in the pool and turn it on. Make sure the pump is set to the appropriate setting for draining water. Monitor the water level in the pool and adjust the pump as needed to drain the desired amount of water. Turn off the pump once the water has been drained to the desired level.


How can I use a pool pump to efficiently drain my pool?

To efficiently drain your pool using a pool pump, you can connect a hose to the pump's outlet and direct the other end of the hose to a suitable drainage area. Make sure the pump is set to the "drain" or "backwash" mode, and turn it on to start draining the water. Monitor the process to ensure the water is being pumped out effectively and adjust the hose as needed to maintain efficient drainage.


How do you enter a sump pump in a basement floor when water from a high water table is continuously pouring in?

Try to find the lowest point on the basement floor. Then either set a stand up pump at the low point, or cut a drain hole and set the pump in lower than the floor at the low point.


What will keep pool pump from sucking water from pool?

The pool pump does suck the water from the pool. Then it goes thru the filter and (if you use have the following) thru the heater and chlorinator then back into the pool. So - nothing will keep it from sucking water from the pool - but that's a good thing. Now - if you set the valve to a different setting - then it might actually send the water to a waste line - maybe that's what you meant. If that's the case -then the pool pump will eventually drain your whole pool if you have it set to get the water from the bottom drain (another valve).


How do you replace the water pump in a 2004 Jeep liberty Sport 2.4 Liter 4 cylinder?

There are fourteen steps on how to replace the water pump in a 2004 Jeep Liberty Sport 2.4 liter 4 cylinder. Some of the step-by-step instructions are set the drain pan underneath the radiator's drain plug, drain the radiator, and then use a wrench to twist the radiator plug counterclockwise.


How do you set the timing on a 1990 Cavalier after changing the water pump?

the water pump is located next to the throttle body. there is no reason to set the timing.


Why does a Camry overheat when the air is set to recirculate?

Low coolant? Cooling fan not working?


Why does swimming pool pump out vacuumed water?

Because the pump is set to "vacuum to waste".


How do you drain an in ground vinyl liner pool?

The best way to empty a pool is with a portable water pump, they have small pumps that can pass 2280 gallons a hour (small 43cc 2 cycle motor and pump). You can buy one or they have them to rent at hardware stores and tool rental places. OR Use the pool's existing pump. Set the spider valve to waste and the suction to pull only from the main drain.


How do you remove the water pump on a 1987 Toyota Camry?

The timing belt has to be removed to access the water pump. Once the pump is replaced the timing belt has to be replaced and set.


Where is the water pump located on a Honda Civic DX?

The water pump is located in the timing set up behind the timing cover its a good idea to replace the timing belt when u replace the water pump


How do you replace the water pump on a 1997 Plymouth Voyager 3.0L?

water pump on this 3.0 is driven with the timing belt. it is internal water pump you will have to set your timing before you start replace your timing belt if it is worn out.