answersLogoWhite

0

No, the bolt assemblies for the Remington 742 and 7400 are not interchangeable. While both rifles are similar in design and function, they have differences in their bolt assemblies that prevent them from being swapped directly. It's important to use the specific parts designed for each model to ensure proper operation and safety.

User Avatar

AnswerBot

17h ago

What else can I help you with?

Related Questions

Are the bolt assemblies on a Remington 580 and 581 interchangeable?

Yes they are interchangeable. The 580 is a single shot bolt action and the 581 is a clip fed bolt action.


Does the Remington sportsman 74 have the same problems as the 742 woodmaster?

The Sportsman 74 is the K-Mart version of the Remington 7400. Internally they are the same. Properly maintained the 7400 is a fine rifle, so the Sportsman 74 should be the same. Both the 7400 and the Sportsman 74 have different internal rail guides that the bolt travels on than the 742 had. Those had been an issue with the 742.


Are there any recalls on 1980 Remington Woodsmaster 742?

There have never been any recalls on the Remington Model 742 that I'm aware of. The Remington 742 is now an obsolete model and was replaced with the Remington Model 7400. The bolt received an upgraded design along with the magazine catch/release. At one time Remington was offering a Model 7400 as a replacement for the Model 742, if you sent them your Model 742 along with $350.00. Is there a problem with the 742 that you have?


You are told you have a Remington Model 721 bolt in your model 700 rifle is that possible?

I'd get in touch with Remington. They can tell you. I would expect that it's possible, as they should be pretty interchangeable, however, it would be unlikely.


What rear axle assemblies are interchangeable for a 2003 dodge ram 1500 V6 3.7L 2wd?

2002 - 2005 Ram 1500 will bolt in, but you need to match the correct ratio.


Install the bolt Remington model 512?

Please tell me how to install the bolt in a Remington Model 512


How do you remove the bolt out of a 7400 270 rem?

If you are asking this question, you should not be removing the bolt from this rifle. If you do not get the bolt locking pins back correct you could be holding a bomb when fired. There are sporting rifle take down books that show the take down for the 7400. best of luck


How do you replace a Remington 7400 extractor?

The Remington Model 7400 extractor is a semicircular shaped part made of spring steel that is held in its correct location with a rivet. This rivet needs to be properly staked in place and blended with the outside diameter of the bolt head. This is a job that should be done by a competent gunsmith that has the correct equipment to do the job properly. The model 7400's extractor was changed from the earlier model 742's which as noted above was riveted in. The model 7400 has a snap in extractor - no rivet. I replaced mine by inserting a curved tool (I modified a small thin screwdriver by bending the tip) through the magazine well under the extractor to pull out the remainder of the old extractor, then snapped in the new one. The new extractor cost 20 dollars (with shipping and tax) from Remington.


What is the vaue of a Remington 700 bolt action 270 EP rifle?

What is the value of a Remington 700 bolt action 270ml rifle?


How do you get the bolt back in a Remington 592M?

how do you get the bolt back in a remengton 592


Will a 5.9 Cummins engine bolt up in a 2008 Dodge Ram 3500?

The 5.9L and 6.7L do bolt up the same, but they are not interchangeable due to emission differences.The 5.9L and 6.7L do bolt up the same, but they are not interchangeable due to emission differences.


How do you take apart a Remington 700 bolt handle off?

The Remington model 700 bolt handle is part of the bolt body and this is a one piece forging.The only way to remove the bolt handle is to cut it off at the bolt body.