If it fits in the chuck straight, yes you can use it. It will be much more effective in a rotary hammer drill though.
The hammer drill vibrates in and out very fast to make masonry drilling much easier. Rotary hammers are drills with a piston on the inside which is operated by the motor and gears. When the motor turns, it moves a gear, which then moves a rod. The rod hits a hammer mechanism which transfers the strike force into the rotary hammer bit. All of this happens very rapidly. Because there is a piston being struck, the force of the blow against the bit is much harder than that of a hammer drill. Hammer drills have a motor that turns a splined gear type mechanism inside the tool. These splined gears are meshed together and hit against each other creating a vibrating action that is transferred to the drill chuck and bit. The hammering is rapid, but the force is only a fraction of that delivered by a rotary hammer. The primary use for the rotary hammer is to drill holes (from 1/4" to 2" in diameter) in hard concrete using a solid bit. It's also used for light chipping. The primary use for the hammer drill is to drill holes (from 3/16" to 7/8" in diameter) in masonry or brick. It's also used as a heavy-duty drill motor for standard drilling. Typically, a hammer drill has a chuck and uses bits that have straight shanks. Most rotary hammers use bits that have either slots and grooves in the shank (SDS) or spline shanks. Also becoming popular is a slotted shank bit called the "SDS-Max" which is for larger hammers. There is a major difference between a standard hammer drill and a rotary hammer drill. A standard hammer-drill uses 2 grooved plates that rotate opposite of each other; when they slip and the grooves connect, a bang is heard, "hammering" the chuck in and out, allowing a carbide bit to go through masonry materials. This method generates quite a bit of noise and often requires hearing protection. A rotary hammer is extremely more efficient than a regular hammer drill, because it drives a piston that compresses an air pocket, that, in turn, pounds the chuck with measurable impact energy. There really is no question which is better and faster. Rotary hammer drills do the same job in far less time, with less noise and with less effort. For many applications, like drilling into tough materials like aged concrete, a rotary hammer is the only tool to use.
The best way to drill into brick using a brick drill bit is to first mark the spot you want to drill, then use a hammer drill on the hammer setting to slowly and steadily drill into the brick. Make sure to use a steady hand and apply gentle pressure to avoid damaging the brick.
To use a hammer drill on brick, first ensure the drill is set to the hammer function. Hold the drill perpendicular to the brick surface and apply steady pressure while drilling. Use a masonry bit and start with a slow speed to prevent damage. Keep the drill moving to avoid overheating and allow the bit to cool. Wear safety goggles and gloves for protection.
I would drill into the brick with a hammer drill and a small bit and use a masonry screw. Lowe's has hammer drills in the $79 - 99 range, or you can rent them at a variety of places. Make sure you are using a hammer drill bit designed for masonry.
To effectively drill holes in concrete, use a hammer drill with a masonry bit. Start with a smaller bit and gradually increase the size. Keep the drill perpendicular to the surface and apply steady pressure. Use water to cool the bit and reduce dust.
An air Impact wrench is a tool shaped a bit like a power drill. It holds special strong steel sockets and applies air power onto a rotary shaft a bit like a hammer drill. Used mostly for undoing very tight nuts especially lug nuts on trucks .
the hammer function on drills is used with a masonary bit and used to drill holes in brick or concrete block.
To drill into granite, use a carbide-tipped masonry drill bit and a hammer drill for best results. Start by marking the drilling spot, then apply firm pressure and keep the drill bit in a steady, perpendicular position. Use water or a cooling lubricant to prevent the drill bit from overheating while drilling.
You could use a hardened steel punch and a hammer; or a drill, or a rotary diamond tool like a Foredom Tool.
To use a hammer drill on concrete, start by selecting the appropriate drill bit for concrete. Hold the drill perpendicular to the surface and apply firm pressure while drilling. Use a slow and steady speed to prevent overheating and ensure precision. Make sure to wear safety goggles and ear protection while operating the hammer drill.
To effectively drill granite, use a carbide-tipped masonry drill bit and a hammer drill. Start with a small pilot hole and gradually increase the size of the hole. Apply steady pressure and use water to cool the bit and reduce dust.
To select and use hammer drill bits effectively, choose the right bit for the material you are drilling into, ensure the bit is securely inserted into the drill, use the correct drilling speed and pressure, and regularly inspect and replace worn bits to maintain efficiency and safety.