answersLogoWhite

0

Hold the outside part with one hand, grab the bumper knob with the other and turn counter clockwise. Then pull it out. There is usually a small hole on the side near the bumper, you will see white, when you're turning the bumper knob you can see that disappear behind a grooved area. Turn in the direction of the groove, all the way til it stops, then it should pull out.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How can I replace the string on a weed eater?

To replace the string on a weed eater, first, turn off the weed eater and disconnect the spark plug. Then, remove the spool housing and take out the old string. Cut a new piece of string to the appropriate length and thread it through the spool. Wind the string in the direction indicated on the spool and secure the ends. Finally, reassemble the spool housing and reconnect the spark plug before using the weed eater again.


How do I perform a Ryobi weed eater string replacement?

To perform a Ryobi weed eater string replacement, first turn off the weed eater and disconnect the spark plug. Then, remove the spool cover and take out the old string spool. Cut a new piece of string to the appropriate length and thread it through the spool. Wind the string in the direction indicated on the spool and secure the ends. Finally, replace the spool back into the weed eater and reattach the spool cover.


What is the best type of string to use for a Kobalt weed eater?

The best type of string to use for a Kobalt weed eater is a high-quality, durable trimmer line that is compatible with the specific model of the weed eater.


How do you change string on skil weed eater?

To change the string on a Skill weed eater, first, ensure the tool is turned off and unplugged or that the battery is removed for safety. Next, locate the spool on the head of the weed eater, press the tabs or release button to remove it, and pull out any old string. Cut a new length of string according to the manufacturer's specifications, thread it through the spool, and wind it tightly before reattaching the spool to the weed eater. Finally, make sure the string is properly fed through the eyelets before use.


How much weed eater string do I need for my yard maintenance?

The amount of weed eater string you need for yard maintenance depends on the size of your yard and how often you use the weed eater. It's a good idea to have at least one extra spool of string on hand so you don't run out in the middle of a job.


How do you restring your bl110 weed eater?

re string a bolens bl110


What size string goes into a weed eater LT7000 string trimmer?

0.080" per 1993 manual


Does the size of the weed eater string matter when it comes to its effectiveness and performance?

Yes, the size of the weed eater string does matter for its effectiveness and performance. Thicker strings are generally more durable and can handle tougher vegetation, while thinner strings are better for lighter tasks. The size of the string can impact how quickly and efficiently the weed eater can cut through grass and weeds.


How do you properly string a weed eater?

To properly string a weed eater, first, turn off the engine and disconnect the spark plug. Then, remove the spool from the trimmer head and unwind any remaining old string. Cut a new piece of trimmer line to the recommended length and insert it into the spool, following the directional arrows. Finally, reassemble the spool onto the trimmer head and secure it in place.


How do you change string head on Kawasaki weed eater?

To change the string head on a Kawasaki weed eater, first ensure the engine is off and the spark plug is disconnected for safety. Remove the old string head by turning it counterclockwise and pulling it off the shaft. Install the new head by aligning it with the shaft and turning it clockwise to secure. Finally, load the new string according to the manufacturer’s instructions, ensuring proper length and winding.


How do I remove the head of a Ryobi Expand-It weed eater?

To remove the head of a Ryobi Expand-It weed eater, you typically need to unscrew the bump knob or cap on the head of the trimmer. Once the knob is removed, you can access the spool and remove it from the head. This allows you to detach the head from the weed eater for maintenance or replacement.


Why is my Ryobi weed eater string not coming out and how can I fix it?

Your Ryobi weed eater string may not be coming out due to a tangled or jammed string, a worn-out spool, or a faulty trimmer head. To fix it, try removing the spool and untangling the string, replacing the spool if necessary, or checking and replacing the trimmer head if it's damaged.