answersLogoWhite

0

Remove the two screws from the recoil pad. There will be a long hole leading to a screw head that attaches the stock to the receiver. Turn the screw counterclockwise until loose. The receiver should slip easily apart. Simply reverse pproceedure to reattach. You'll need a standard long shank screwdriver for the stock/receiver screw and a Phillips for the recoil pad.

The receiver is completely modular and nothing will "fall apart" after the two parts are separated...

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you remove safety on Baikal shotgun?

You dont, you keep it on.


How do you remove a butstock on a pump action shotgun?

only when you shoot it!


How do you remove the forend from a Glenfield Model 30?

Do you have the pump shotgun or the lever-action rifle?


How do you take the barrels off a baikal ou toz 34fp?

To remove the barrels from a Baikal TOZ-34FP shotgun, first ensure the firearm is unloaded and safe. Then, locate the barrel release lever, usually found on the underside of the action. Press or pull the lever while simultaneously lifting the barrels upward from the receiver. Once the barrels are detached, you can proceed with cleaning or maintenance as needed. Always refer to the manufacturer's manual for specific instructions and safety precautions.


How do you remove the bolt from a jc Higgins model 101.25 410 bolt action shotgun?

First remove the screw opposite the bolt. Operate the bolt as if you were cocking the gun, pull the trigger and it will slide out.


Can you remove the barrel from a sears and roebuck model 66 shotgun?

Yes, you can remove the barrel of a model 66 Shotgun!


How do you remove the extrators from a jc higgins model 10 12 gauge bolt action shotgun?

To remove the extractors from a J.C. Higgins Model 10 12-gauge bolt-action shotgun, first ensure the firearm is unloaded and safe. Next, disassemble the shotgun by removing the forend and barrel. With the bolt removed, you can access the extractors, which are typically held in place by small pins or screws. Carefully tap out these pins or unscrew the fasteners to release the extractors from the bolt assembly.


How do you remove the magazine tube from Charles daly 20 gauge shotgun?

To remove the magazine tube from a Charles Daly 20 gauge shotgun, first ensure the firearm is unloaded and the action is open. Locate the magazine cap at the end of the magazine tube, unscrew it counterclockwise, and then carefully slide the magazine tube out of the receiver. Depending on the model, you may need to remove additional components, such as the forend or any retaining screws, to fully detach the tube. Always refer to the specific owner's manual for detailed instructions related to your shotgun model.


How do you remove the barrel from a western field shotgun?

with a hacksaw


Where is the measurements made on barrel of sawed off shotgun?

Close the shotgun action and insert a rod down the barrel to the standing breech (to the rear edge of the chamber or where the back of the shotgun shell would be). Mark the end of the rod protruding from the barrel. Remove the rod and measure its length. Per federal law (GCA 1934), this must be a minimum of 18"


How do you remove the bolt from a J.C. Higgins shotgun model 538-1101?

To remove the bolt from a J.C. Higgins shotgun model 538-1101, first ensure the shotgun is unloaded and pointed in a safe direction. Open the action to expose the bolt assembly, then locate the bolt release mechanism, usually found at the rear of the receiver. Depress the release and carefully pull the bolt out from the rear of the receiver. Always refer to the owner's manual for specific instructions and safety precautions.


How do you remove the bolt action from a Sears 12 gauge shotgun?

If it is a J.C. Higgins bolt action shotgun, there is a small set screw on the left side of the receiver top between the bolt handle and the ejection port. Use a flat tip screwdriver and take out that screw. It is litterally the metal peg that the bolt is running back into. Without the screw, the bolt comes straight out the rear.