answersLogoWhite

0

An 18 mm wrench is ideal, but if you don't have one of them, you probably won't have a 23/32 either.

User Avatar

Wiki User

12y ago

What else can I help you with?

Related Questions

What woman's jeans size fits 50 hips?

18/20


What size of wrench needed to remove calipers on 2000 Dakota 2wd?

18 mm I think.


What size socket fits a DPR6EA-9 NGK spark plug?

18 mm


What size socket fits a 1994 Toyota celica wheel nut?

I believe that is 18 mm.


What size of wrench is needed to remove 2003 Silverado front caliper bolts?

the caliper bracket bolts use 18 mm wrench on a 03 1/2 ton 4x4


A 18'' Audi rims with 5x112 pattern fits on Pontiac grandprix with 5x115 lug pattern?

No, the bolt pattern is different and the Audi wheel's bolt holes will not match up to the grandprix therefore being unable to bolt up to the grand prix's hubs.


What is the Pontiac Solstice GXP bolt pattern?

The Specs on the Solstice GXP are: 5 x 110mm bolt pattern 55mm Offset 18" x 8" size


You were wondering will 18' rims work on a 2005 dodge neon sxt?

yes they will, tire size is 215/35/18, just make sure the bolt pattern is 5x100


How do you replace the shocks for 2000 Dodge Durango?

Rear shocks: You will need 15 and 18 mm sockets or wrenches, but combination wrenches will work as well. First, place your vehicle on jack stands and also support the side you are doing with a jack. (If you remove the spare tire it will give you a lot more room to work.) Second, coat the bull pens (bolts that attach shocks to vehicle) with penetrating oil (like WD-40) and let set for a while. Then put you 15 mm socket on the bolt and the 18 mm wrench on the nut and controllably push the socket and pull the wrench to loosen bolt then remove all the way leaving the bolt on. On the top side you will want a socket extension. Put the wrench and socket on the same things as last time, but because it might be rusty you will have to work the 18 mm on to the nut. When you start removing the bolt only use the socket and let the wrench go where it wants because it should run in to another bolt that will hold it in place. Once loosened, remove again leaving the bolt on. Then take your wrench and hit the bolt so it comes out. After you get the bottom bolt out you should be able to pull the top on out. Once both bolts are out remove shocker. To put new ones back on just reverse the order. (Note: If you are replacing with gas shocks you will have to push them up a little bit. You might also have to use the wrench to get the bolt back in.) One more thing: When putting the nuts back on start them by hand then use the tools to get them on all the way. And tighten as tight as you can. I am not sure how to change the front shocks (if any) so you are on your own with that.


What is the price of a pack of diapers in 2007?

Depends on the size, but a 56 pack of #1 diapers(fits 8-12 lbs.) cost almost $18.


Installing brake calipers on a D21 1990 Nissan pickup truck?

Be careful to put the calipers on the correct sides. The bleeder fittings must be up when the caliper is being installed correctly. If not, you will not be able to correctly bleed the brakes.You'll need a 10 millimeter socket or wrench, an 18 millimeter or a 3/4" socket, with a half inch drive, a half inch drive socket wrench and a half inch drive breaker bar. The calipers are held with two 18 millimeter bolts on each caliper. One bolt is long and the other is short. They both bolt through the caliper.There is a third bolt this size holding the steering control arm and does not need to be undone.There is also a10 millimeter bolt holding the rubber hydraulic line to the back of the caliper. It has two copper washers, one on each side of the fitting that are bolted to the caliper.


What size square fits into an 18 circle?

A square whose diagonal is the diameter of the circle. So, if it is a circle with diameter 18 units then the diagonal of the square is 18 units and so its side is 9*sqrt(2) = 12.7 units.