0
No the circuits are not designed to handle video frequency
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What do two way radios do function wise?
Two way radios can both transmit and receive signals. It uses two different radio frequencies to carry the two conversations simultaneously.
How many pins are there in an S-video connector?
Four + shield. S-Video is a step-up from Composite video which uses only two pins to transmit a composite (which means luminance (brightness) and chroma (color) signals 'mixed' in such a way to transmit them over one pair of cables). S-Video separates these two signals, so it needs four pins -- one pair for the luminance information, and the other pair for chroma information. For more info, please refer to Wikipedia article "S-Video".
How far does the signal reach for a cb two way radio?
Typically, the signal that the cb two way radios can transmit would go up to a few miles on a good day. However, the likelihood is more likely that the signals will only travel one or two miles.
How do motorola 2 way radios transmit a signal?
Two way radios should be set at the same frequency. Then, 2 or more persons can communicate with each other via those radios, by pressing buttons and speaking.
How does the Motorola two way radio work?
The Motorola Two-Way Radios are new products produced by Motorola company. Motorola Two-Way radios are used to transmit and receive messages allowing the operators to communicate with each other.
When using a walkie talkie why does your voice get tight when you are in a tight spot?
Mainly stress. Answer People need to remember to talk normally when using two-way radios. No extra voice skills are needed to transmit voice signals - if you talk calmly, your message will be clearer and better understood.
What devices uses radio waves?
Radio waves are used to help transmit signals between two devices.Some devices which use radio waves are:RadiosTelevisionsMobile (cell) phonesCordless telephonesNavigational devices (such as GPS and satellite tracking)RadarRadio-tuned clocks and watchesRadio telescopes
How do you transmit 2 video signals down one cable?
Generally it isn't possible to send two video signals on a single wire although there are instances where it can happen. Video over Ethernet allows multiple signals to be sent in packets although the nature of Ethernet means that the signals will each have a delay so synchronizing the signals may be difficult. Video over CAT5 uses converters that take a video signal and modify it to run over a single pair of a CAT5 cable. Normally, two more pairs would be used for stereo audio. If mono audio is used, it is possible to run two composite video signals with audio down one cable. Note that video over CAT5 uses the same cable as Ethernet but employs a very different signal format to Ethernet. Composite video signals use a single cable but in fact, the signal has three separate video components encoded into the signal. The signals are one for brightness and two for color information. Together they make up a full color signal and can be separated into the three components at the far end. Although the cable carries three signals, remember that they are all parts of the same color signal so this probably doesn't qualify as two signals. Finally, cable broadcasters use encoding systems to allow numerous signals to be carried on a single cable. The one that enters a house to supply a cable receiver carries many signals with just one being decoded and output by the receiver. This takes complex hardware at both ends so is outside the scope of most home users.
What is radio communication?
Radio communication is the transmission of information through radio waves between two or more devices. It is used for various purposes such as broadcasting, two-way communication like walkie-talkies and cell phones, and communication with satellites and spacecraft. Radio communication relies on frequencies within the radio spectrum to transmit signals over short or long distances.
Does cell phones have radiowaves?
Yes. A cell phone is basically a phone connected to two radios, One radio tuned to listen and one radio to transmit what you say.
What are two way radios used for?
Two way radios are used to transmit and receive. What I mean by that is a two way radio allows two people to talk to each with similar devices on the same radio frequency. It's rather unique! One (the operator) can talk, and the other listen. This device allows police officers, detectives, and many other jobs easier.
Does an S Video cable also carry audio?
S-video is a two part video signal carrying luma and chroma signals (Brightness and color signals). There is no audio signal in an S-video connection so the audio will need a separate connection to operate.
