how to work a project on speed breaker energy
13,600 miles per second :-) True dat
start generator, plug in variable speed drill, set drill to forward, squeeze trigger, quickly spin drill in reverse by hand. be sure generator main breaker is on.
Pre 1970 (72?) breakers were specified with a MVA assymmetrical interrupting rating. Breakers are now spec'd with a symmetrical rating, which is provided in amps or kA. There is an ANSI standard that provides conversion from assymetrical to symmetrical and vice versa. Converting from Asym. to symmetrical involves analyzing the open close interval, time between successive openings, breaker operating speed, breaker operating voltage, and whether the breaker is connected to a generator bus or not (usually has an unusually high X/R ratio which results in more DC offset). So...it is the interrupting rating, or how much (short circuit) power the breaker can interrupt. The faster the breaker operates, the higher the voltage, the closer it is to a generator, and the more times it is expected to open results in a lower interrupting amperage capability. If it is used beyond this rating, it is likely to internally fault when attempting to open.
initial torque to overcome the friction in generator and then to keep constant speed of stator within the generator. Minimum 50NM
By 'speed of electricity', presumably, you mean 'speed of current'? We don't normally measure the speed of current but, rather, its intensity. The unit of measurement of current is the ampere (A), which is one of the SI system's seven base units. The ampere is defined in terms of the force a current produces, due to the magnetic field surrounding it, between two, parallel conductors.
Yes
you press R3
The speed of computers increased from one generation to the next generation, and to the next generation, and so on.
it is very flexible and can be transported to very long distances at the speed of light which is not possible in other form of energy. Electricity is neither available nor required in Electric form. consumption and generation of electricty should be done at a time
No; while the speed of light is a constant, the speed of electricity is dependant on many cofactors.
Approximately the same as the speed of light.
The minimum speed of 6v motor to produce electricity is 15 Mph.
Because electricity is the movement and flow of electrons, which are matter. Since they are matter, they cannot reach the speed of light.AnswerBy the 'speed of electricity' you presumably mean the 'speed of charges through a conductor'? (Remember 'electricity' is not a quantity!). The answer is that they move through a conductor v-e-r-y slowly -for normal conductors, just a fraction of a millimetre per second!
the g stands for generation its the 3rd generation of internet speed development
The speed of lightning is somewhere between that of light and sound which is why most scientists would agree that the speed of light and the speed of sound make a good comparison to that of lightning and electricity.
Next time on the roads, don't scoff at the speed-breakers. They could actually light up small villages off the highway. An amateur innovator in Guwahati has developed a simple contraption that can generate power when a vehicle passes over a speed breaker. Kanak Gogoi, a small time businessman, has developed a mechanism to generate power by converting the potential energy generated by a vehicle going up on a speed breaker into kinetic energy. The innovation has caught the eye of the Indian Institute of Technology (iit), Guwahati, which will fund a pilot project to generate electricity from speed-breakers. The idea is basic physics. Gogoi has welded five-metre-long metal plates into the speed-breaker instead of the conventional bitumen-and-stone-chip rumble strip. The plates are movable and inclined with the help of a spring-loaded hydraulic system. The fulcrum-attached plates are pushed down when a vehicle moves over them and bounce back to original position as it passes. "When the vehicle moves over the inclined plates, it gains height resulting in increase in potential energy, which is wasted in a conventional rumble strip," Gogoi says. "When the plates come down, they crank a lever fitted to a ratchet-wheel type mechanism. This in turn rotates a geared shaft loaded with recoil springs. The output of this shaft is coupled to a dynamo to convert kinetic energy into electricity," he explains. iit Guwahati has evaluated the machine and recommended it to the Assam ministry of power for large scale funding. A K Das, a professor at iit's design department says it is a 'very viable proposition' to harness thousands of mega watts of electricity untapped across the country every day. "A vehicle weighing 1,000 kg going up a height of 10 cm on such a rumble strip produces approximately 0.98 kilowatt power. So one such speed-breaker on a busy highway, where about 100 vehicles pass every minute, about one kilo watt of electricity can be produced every single minute. The figure will be huge at the end of the day," he said. The Assam power ministry is expected to back the iit pilot project. Das says a storage module like an inverter will have to be fitted to each such rumble strip to store this electricity. The cost of electricity generation and storage per mega watt from speed-breakers will be nearly Rs 1 crore as opposed to about Rs 8 crore in thermal or hydro power stations
yes