Shut off fuel supply. Allow to cool. Close the inlet and out let valves. Open the drain valve bottom of heater. Open the T&P to break Vacuum. Have a hose attached to dump water in a safe area.
If you are draining heater to flush don't shut off fuel supply. On a power vent heater (pvc venting) you can turn the switch off. On a conventional heater with metal flue pipe turn to the vacation setting (lowest temp setting). when your heater is refilled you can switch on or turn temp setting to original position without bleeding gas and relighting. Waiting for a sitting heater to cool will take hours. You can run hot water in house with heater off until cold. You should not have an outlet valve on a hot water heater if you do remove it. Open hot water in building to vent. Opening and old T&P will weaken the spring even more so if hot water runs through it and may cause it to fail (drip) later with water on. Some drain valves drip later with water on have a 3/4 garden hose cap with washer for valve if it leaks as opposed to replacing drain valve.
Depending on what type of water heater you have there should be a plug or valve at the base of the water heater
With an approved automatic bleeder valve
Side of water heater, near bottom.
Yes. I would. If you are replacing the hot water lines, it is also a good time to drain the hot water heater and get rid of all the junk at the bottom of the hot water heater. That should be done once a year. Your hot water heater must be off when you do that, your hot water heater should be off when you drain your hot water heater. You will see boiler scale come out of your water heater. Leaving the boiler scale in your water heater makes it less efficient. It makes it harder to heat your water. It is the same as throwing money down the drain. If you want to give your money away, you should give it to the Salvation Army instead of the Utility Company.
The hot water valve should always be open, so the hot water can exit the heater into the system. If your actually meaning opening the drain valve on the bottom of theater, the water in the heater will drain, starting with the hot water stored there, and then the cold water that is entering the tank to replace it will simplt flow out the bottom before being heated. Dpending on where the heater is located will denepnd on how much of a mess the ensuing flood will be.
Not directly.
According to DIY on Hot Water Promblems if theres not enough water then you hit the reset button. If the water is too hot then change the temperature and reset. If you have a leaky heater then you need to replace the valve. If you have a rusty tank then you need to replace the water heater. If you have a noisy heater then you need to drain and flush the tank. If you have dirty water then drain and flush the tank and do it on a regular basis.
No, you have to attach a garden hose to the fitting at the bottom of the tank. Often the tank will have sediment built up in it and the water will drain very slowly from this.
At the bottom front edge, there should be a hose connection. Attach a garden hose to it and then open the valve. Because sediment can collect at the bottom of the heater, they can drain slow sometimes, but it should drain eventually. Turn the heater off before draining.
By Andreina Urdaneta A clean water heater will heat and maintain water better and last longer. Once a year, flush your water heater, and in extreme hard water areas, at least twice a year. If you feel up to the challenge, here are some tips to help you in a basic cleaning. 1 Turn the water heater and the cold water supply to the water heater off. 2 Hook a high-quality garden hose to the drain valve, and place the other end in an area where hot water will not cause damage. 5. Open the drain valve. 6. Disconnect the cold water pipe on the top of the water heater. This step will let air into the water heater so it will drain. When the water heater is empty, close the drain. 8. Pour tile cleaner into the cold water, leave for a couple of hours and drain the detergent out of the tank. 10. Reconnect the cold water supply to the water heater. Open the cold water valve and let the water heater flush for a couple minutes. 12. Close the drain valve and open the hot water faucet nearest to the tank, and let the water heater fill. 13. When water starts to come out of that faucet, reopen the drain and let the water heater continue to rinse. After all the air is out of the water heater, turn it back on. Take care of your water heater, and it will take care of you. If you keep ignoring the task, your water heater may just leave you in the cold.
No, cold wter enters the water heater at the bottom of the tank, right where thee valve is.
It would help as most of the rust accumulates at the bottom of the tank.
If electric shut off the current to the elements, if gas shut off the gas valve. Open a hot water faucet to give it air, open the drain valve on the bottom of the heater.
It is a water heater, not a hot water heater. There would be little point in using a hot water heater. I assume that is your point.