I'm going to assume you're referring to the frequency of AC (Alternating Current) and I'm going to assume that you're asking because you have some device that wants 50Hz and you are faced with a 60Hz supply. That is a lot of assumptions but you didn't give a lot of information.
It is possible but you'd have to convert the 60Hz AC to DC then back to 50Hz AC. It would involve some expensive equipment. I'm not aware of a one-box solution but you could piece together a system with an AC-DC battery charger, adequate storage batteries, and a DC-AC power inverter. Depending on your application, you might be better off replacing the equipment that won't run on 60Hz.
Before running off and spending your money on this, check the labels for your equipment. The label on my laptop power supply says it accepts 110vac-240vac at 50/60Hz. If you're going to run into problems it would most likely be with electric motors.
Yes it is possible. One way to convert from 50Hz to 60Hz would be to first convert the 50Hz source to DC and then convert the DC to 60Hz using a 60Hz inverter. This is an entirely solid-state solution. The advantage being the conversion efficiency is very high. Also not having any moving parts makes this very reliable (provided cooling is good). The drawback is that the output may not be a "true" sine wave and may have a higher harmonics level. The result being more noise. But there are very few devices which would need anything better than this solution.
If the power is being produced by a generator the frequency can be controlled. The frequency is governed by the speed of the generator. Lower the revolutions of the generator will lower the frequency the generator produces. Increase the revolutions of the generator and the frequency will increase.
You could also use static inverters. Use a 12 vdc or 24 vdc inverter designed for the American market. Transform and rectify the 50hz power down to the 12 or 24v, required for the inverter.
A rotary converter would use a 50hz motor to drive a 60hz AC generator.
If you're trying to use a 60 Hz outlet to run a 50 Hz appliance, that that would take electronics
so complex and expensive that it's definitely not worth your time, money, or effort.
==============================================
Another contributor added:
if it rpm, you need 3600 rpm for 60hz 3000 rpm for 50hz (for 1 pair of north, south magnets)
When equipment is designed by the manufacturer it is designed for the frequency it is to be operated on. Some pieces of equipment are designed to be operated on both frequencies. The only way to convert 60 Hz to 50 Hz is if the 220 volts was being produced by a generator under your control. Slow the generator down while watching the frequency meter until it gets to 50Hz. Then raise the excitation voltage until the voltage rises to 220 volts.
yes you can, but the cost is double the convertion of voltage 110 to 220 volts. all what you need is to convert to dc then from dc back again to ac with any rate you like
We can convert the 60 Hz wave into 50 Hz by using the CYCLOCONVERTER.
by using a chopping circuit.
No
You don't.
ONE THING FOR SURE THERE IS NO CHANGE IN VOLTAGE IF SAME EQUIPMENT WE ARE TALKING ABOUT. THE ISSUE HERE IS THE CHANGING LOAD FREQUENCY 60HZ TO 50HZ OR VICE VERSA. FOR EXAMPLE THE MOTOR HORSEPOWER AND R.P.M. WILL BE APPROXIMATELY 90 AND 83 PERCENT OF THE NAMEPLATE SPECIFICATIONS, ALSO THE FULL LOAD RUNNING TORQUE WILL INCREASE APPROXIMATELY 8 PERCENT IF USED FROM 60HZ TO 50HZ.
You can get a transformer that converts the UK's 230V power to 120V, but you cannot get a transformer that will convert from 50Hz to 60Hz. Often, US equipment can work, except that they will work hotter and less efficiently on the 50Hz power. Consult your clipper and trimmer documentation - you may find that it will work just fine on 50Hz.
It will not work at all.
What effect will be there on the motor (Induction) output power when a 100kW 50hz motor is connected to a 60hz power supply.
you can't
You don't.
No 50Hz
10HZ. Enjoi!
yes
ONE THING FOR SURE THERE IS NO CHANGE IN VOLTAGE IF SAME EQUIPMENT WE ARE TALKING ABOUT. THE ISSUE HERE IS THE CHANGING LOAD FREQUENCY 60HZ TO 50HZ OR VICE VERSA. FOR EXAMPLE THE MOTOR HORSEPOWER AND R.P.M. WILL BE APPROXIMATELY 90 AND 83 PERCENT OF THE NAMEPLATE SPECIFICATIONS, ALSO THE FULL LOAD RUNNING TORQUE WILL INCREASE APPROXIMATELY 8 PERCENT IF USED FROM 60HZ TO 50HZ.
You can get a transformer that converts the UK's 230V power to 120V, but you cannot get a transformer that will convert from 50Hz to 60Hz. Often, US equipment can work, except that they will work hotter and less efficiently on the 50Hz power. Consult your clipper and trimmer documentation - you may find that it will work just fine on 50Hz.
Voltage has nothing to with frequency
One way would be to hook it up to a supply (by itself, with no load) and measure the speed with a contact tachometer. If your supply is 60Hz, and the motor speed corresponded to one of the standard motor speeds, it would be a pretty safe bet you had a 60Hz motor. If the speed was about 20% faster than a standard speed, the motor is probably a 50Hz motor. Or 20% slower if you were running a 60Hz motor on 50Hz For instance, a 1750 RPM 50Hz motor would spin at about 2100 RPM if you ran it on 60Hz.
The internal working of the motor is designed for 110V/60Hz. Your stepdown converter is from 220V/50Hz to 110V/50Hz. Frequency converters from 50Hz to 60Hz are very expensive (many times the cost of a new clipper). Therefore it is better you get a clipper designed for 220V/50Hz. If you still like to put your clipper to use, then the most cost effective solution would be to get a "car inverter" that would convert 12V DC to 110V/60Hz AC.
No! Normally not, the recistance in the windings is to hig on 60Hz and the pump motor has not power enough to work propelly. This happened to myself when I connected my Whirpool AWE 7519 to 230V 60Hz. Europian model for 50Hz.
No, 120 v is not enough.