answersLogoWhite

0


Best Answer

I had the same problems, turn the ignition on (without starting car). Then shift the truck into reverse and back into park. If you look under the steering wheel on the bottom cover right behind the wheel you will see a round cap about 3/4" round. pop it off and there is a hole that you can push a pen or nail up in to the hole and hit a release switch. I put a bolt in it. remove the bottom cover of the steering wheel calm and drop a 3/8 X2" bolt in the hole and put the cover back on and cut the bolt off so you don't hit it with your knee. when the key get stuck just push the bold up and turn the key. its like some of the old cars that you had to push a button to turn the car off.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove a key that is locked in the ignition on a 2000 GMC Jimmy?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you check the operation of the fuel pump on a 2000 gmc jimmy?

being that fuel pump is in the gas tank I would remove the fuel line at the filter then turn on ignition being that fuel pump is in the gas tank I would remove the fuel line at the filter then turn on ignition


How do you remove the ignition cylinder on a 2000 Lexus RX300?

To remove the ignition cylinder on a 2000 Lexus RX300, first remove the vanity engine cover by unscrewing it. Disconnect the wiring connector by pushing the clip that holds it in place. Finally, remove the bolts that hold the ignition cylinder.


How do you replace ignition switch on a 2000 silverado?

Remove the ignition switch retaining ring. Pull the ignition switch out. Remove the wiring harness from the back of the ignition switch. Reverse the process to install the new ignition switch.


How do you start a 2000 XK8 jaguar when the ignition is locked?

You probably just need to turn the steering wheel slightly.


How do you remove the ignition lock cylinder on a jaguar x-type?

Remove the retaining ring from the top of your 2000 Mercedes-Benz ignition lock cylinder. Slide the ignition lock cylinder out and remove the wiring harness.


How do you remove ignition switch cylinder from 2000 Chevy astro van?

You can remove the 2000 Chevrolet Astro Van the ignition switch cylinder by removing the retaining ring. The retaining ring will need to be turned to the left. The ignition switch cylinder will slide out.


How do you replace an ignition switch for a 2000 blazer?

You will need to remove the retaining ring at the top of your 1978 Chevrolet Blazer ignition switch. Slide the ignition barrel out and remove the wiring harness. Reverse the process to install the new ignition switch.


How do you replace an ignition switch in a 99 suburban?

how DO YOU REMOVE AN IGNITION CYLINDER FROM A MALIBU CHEVROLET 2000


How to remove 2000 explorer ignition switch?

First you will have to remove the who steering wheel surrounds. Once this is removed, you will see the screws that are holding the ignition switch in place; remove those screws and then unhook all the wires.


How do you open hood on 2000 GMC Jimmy when the hood release cable has broken?

You will need to remove the grill from your 2000 GMC Jimmy. With the grill removed. You can remove the hood latch retaining bolts. The hood will be released with the latch bolts removed.


Removing ignition switch on a 2000 Chevy Astro van?

If you need to remove your ignition switch, you should consult your owners manual. Check for a guide on how to remove and replace and follow the instructions.


Where is the starter located at on a 2000 gmc jimmy?

My 2000 GMC Jimmy is slow cranking. The battery voltage meter is showing charged so I am assuming that the starter is the problem. Where do I find the starter to remove it?