What would you like to do?
"Mechanic in a can" get some engine clean, diesel, or some trans fluid; drain a quart of oil out of the engine; then put a quart of what ever you got in to the engine replacing the oil you just drained; run it till it's warm, drain it all out and change the oil and filter; start it up check for leaks and see if your noise is gone; repeat if nessesary; do not drive around for 3000 miles. you can try this with marval mystery oil too.
2 people found this useful
Was this answer useful?
Thanks for the feedback!
If you have a 6 cylinder 3.0L the timing marks are located on the crankshaft gear for the timing belt (its just a notch on the rear of the gear just spin it clockwise until …you find it) that lines up with a notch that sicks out from the block just above it. The camshaft marks are little arrows on the camshaft gears which line up with little marks on the cover plates that close the back of the gears in (about 1 o'clock)
Discard the valve all together and plug the vacuum line as if there was no bypass valve
Answer . slide radiator down into position behind the radiator support\nattach the air conditioning condenser to the radiator if so equipped,with force of 10Lbs to seat th…e radiator assembly lower rubber isolators in the mount holes provided\ntighten the radiator mounting screws to 9 ft. lbs.\nconnect the automatic transaxle hoses,if so equipped,tighten the hose clamps to 35 inch lbs\nslide the fan shroud,fan and motor down into the clips on the lower radiator flange .install new shroud retaining clips\ninstall upper and lower radiator hoses including the coolant reserve hose\nplug the fan motor electrical connection and attach the negative battery cable\nfill the cooling system with coolant
Answer On my 94, (same engine) the belt broke and when it was replaced (big job) it ran just fine.
Answer On the front of the Throttle Body, its held in by 2 Star Screws.
Low coolant? Bad thermostat? Heater core plugged, restricted, or airbound? ======= Good answers by original poster. I would recommend replacing the t-sta…t first. Its pretty straightforward. If that doesnt solve your problem, our 89 acclaim's have a heater valve (it shuts off coolant flow to the heater core when the a/c is activated to increase the efficiency of the a/c) by the firewall that can stick or lose vacuum (broken vacuum line). Check that next. Lastly, I would take the lines off the heater core and run a garden hose up to it. This will "backflush" any accumulated crud out of the heater core. I do this to my Acclaim every fall and cant believe the crap that comes out! ======= When the heater went out in my car, I went in and found out that it was the heater control valve. Check it out.
What kind of refrigerant does a 1993 Plymouth Acclaim use that has a service valve on the compressor that looks like a tire valve?
if the cap is green, your ac system uses R22 coolant. If it's PINK, then it uses R410a coolant
The cost of a valve tap repair will vary based on various factors. If you do it yourself, it may cost about $40 but if you take to a profession mechanic, you can pay up to… $60.
Next to the incoming air hose to the the air cleaner... air cleaner inlet... on the drivers side fender.
On my 1990 it is the middle relay on the left fender between the battery and the shock tower.
1995 Plymouth Acclaim Repair Fuel Pump Steps or Procedure? What I need to do to remove the Fuel Pump and put the new one in? Does the pressure gas is off ones …the Fuel Pump is not working? Does I need to remove the negative cable of the batterry and open the outside gas tank cap or lid? "Please as soon you can answer, sent the answer to my e-mail address", as follow; email@example.com Thanks, Miguel A. San Antonio
The black radiator hose comes out of the upper left of the radiator. Follow it to where it connects to the engine block at the top center of the engine. It is just to the left… of the ignition coil. That is the thermostat housing. Remove the bolts holding the housing, and the thermostat will be there.
according to a Chrysler technical bulletin on this issue you need to drill a small hole in the top center of the plastic housing that surrounds the headlight. this will allow …moisture out.
Yes it can be repaired to a point. There is a tool called a reseater which grinds the valve seat to make it smooth and grind out fine cracks. The seat can only be …reseated a number of times before its too flat in which case the tap would then need to be replaced.
what are the vavle timing mark's for a 1994 Plymouth acclaim