0
yes, their are many types of hydraulic oils, for different specificate duties machine,s apply to.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is an example of a hydraulic system?
Force that is applied at one point is transmitted to another point using an incompressible fluid. for example a lift cylander on a dump truck
Can you put water in a hydraulic jack?
you can but you'll be buying a new one very shortly afterwards. Use hydraulic fluid. Brake fluid works well also
How do you see the level of a hydraulic excavator?
If you mean to the level of hydraulic fluid, it is usually a glass pipe with indication marks mounted on the hydraulic tank. You can usually find it behind one of the rear access panels.
Working peinciple pf hydrualic cylinder?
Hydraulic fluid pressure cylinder with one hand and moving the piston to produce work.
How hydraulic rock breaker works?
Hydraulic rock breakers are powerful percussion hammers. The rock breaker works on the principal of hydraulics, where putting pressure on one part of a fluid transfers pressure to all areas of the fluid, allowing a multiplication of force.
Can I use hydraulic fluid for a substitute for hydraulic oil in a bobcat skid-steer?
Hydraulic fluid and hydraulic oil are one in the same.
What explains about hydraulic devices?
Question isn't clear. A hydraulic cylinder is one tube inside of another tube. Fluid is pumped into the larger one under pressure and this forces the smaller inside one to extend. It doesn't have to be fluid, an impact wrench or air drill is the same principal using air.
Is power steering fluid hydraulic fluid?
There are many different specification and types of Hydraulic fluid. A specific power steering fluid for one car model may not work for all cars. So be careful when you substitute different fluids. Hydraulic fluid used in aircraft is different from that used in cars. The fluid used in shock struts and landing gears are different. Swapping fluid can cause the seals to weaken and result in leaks. The term "hydraulic fluid" can be a generic word for any fluid used to power a mechanic device.
What is an example of a hydraulic system?
Force that is applied at one point is transmitted to another point using an incompressible fluid. for example a lift cylander on a dump truck
What is transmission fluid used for?
Transmission fluid, like in automatic transmissions of cars, is used to transfer the power of the engine to the drive shaft. It's a hydraulic fluid, and the transmission is a hydraulic pump and a hydraulic drive all in one. The motor drives the pump (the torque converter), and it compresses the transmission fluid which in turn drives the clutch assembly.
Can you put water in a hydraulic jack?
you can but you'll be buying a new one very shortly afterwards. Use hydraulic fluid. Brake fluid works well also
How do you see the level of a hydraulic excavator?
If you mean to the level of hydraulic fluid, it is usually a glass pipe with indication marks mounted on the hydraulic tank. You can usually find it behind one of the rear access panels.
What is directional valves?
Directional control valves are one of the most fundamental parts in hydraulic machinery. They allow fluid flow into different paths from one or more sources. They usually consist of a piston inside a cylinder which is electrically controlled. The movement of the cylinder restricts or permits the flow, thus it controls the fluid flow. Directional control valves are mainly two types: Hydraulic and Pneumatic. Hydraulic directional control valves are for a liquid working fluid (e.g. water, hydraulic oil) and pneumatic directional control valves are for a gaseous (usually air) working fluid.
Working peinciple pf hydrualic cylinder?
Hydraulic fluid pressure cylinder with one hand and moving the piston to produce work.
Where is the clutch cable on a 1991 Mazda miata?
Isnt one, its hydraulic, and its next to the brake fluid resevior
What is hydraulic multiplication?
hydraulic multiplication is using incompressible fluids to transfer force from one are to another and in the process multiply the force being transfered. because pressure remains constant in a closed system, such as this, the pressure in the fluid is equal, it is constant, it does not change, therefore the bigger the area, the bigger the force.
How does a 4 way hydraulic valve work?
4 Way hydraulic valves are often used with double acting cylinders. The valve usually has a handle that is used to change fluid direction. On the 4 way valve there will typically be 4 ports or openings for connections of hoses. Connecting hoses is done as follows: There will be an IN and OUT port and there will be an A and B port. (Different manufactures label differently so sometimes ports A & B are labeled 1 & 2 for example.) The in port is where the hose for fluid under pressure is connected. This may be from a hand operated or motor powered pump. The out port will be connected to the hose going to the fluid reservoir or tank. The A and B ports will be connected to the hydraulic cylinder. Now for the how it works part: Basically the handle controls a piston inside the valve. The piston is machined to allow fluid to run through it in different directions depending on the location inside the valve. There are two fluid paths inside the valve at the same time with fluid running two directions. One path is for the supply hydraulic fluid and one path is for the returning hydraulic fluid. When hydraulic fluid is pumped into the IN port and the handle is pushed one direction the fluid passes from the IN port and goes out the A port leading to one line or hose to the hydraulic cylinder. At the same time the valve allows fluid returning from the other hydraulic hose connected to the cylinder to come into port B and go out the OUT port on the valve back to the hydraulic tank. When the handle on the valve is pushed the opposite direction the fluid paths switch so the pumped fluid coming in the IN port goes out the B port to the hydraulic cylinder and fluid returns coming into the A port and goes through the OUT port back to the hydraulic tank. The 4 way valve allows fluid to run from the pump or (hydraulic fluid source) to the hydraulic cylinder in two different directions depending on the position of the handle so the cylinder can either be extended or retracted. When the handle on a valve is not pushed in either direction it is called a neutral or normal position. Some 4 way directional valves only allow fluid to pass when the handle is moved in one direction or the other while some allow the fluid to come into the IN port and go through to the OUT port when it is in the neutral position. The valves that allow fluid to pass from the IN to the OUT while in the neutral position are often used with powered hydraulic pumps. Once the pump is turned on the fluid begins to flow in and out of the valve until the handle is moved to direct fluid to the hydraulic cylinder.
