0
A: a transformer will follow the rule of input output ratio with no load. As soon as a load is applied there will be changes in the ratio
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
The current load of a transformer is the current drawn by the?
load
What is the load side of a transformer?
The load side of a transformer feeds the device, such as a light or motor. It is the output of the transformer. The input, or line side, provides the voltage that is to be transformed, either up or down, to supply the load side.AnswerA transformer's primary winding is connected to the supply voltage, and the secondary winding is connected to the load.
What are the approximation of open circuit and short circuit test of transformer?
A short-circuit test is done to determine the power lost in the resistance of the primary and secondary windings of the transformer. It is done at full load current but with only enough voltage to give the required current with the secondary short circuited. An open-circuit test is done at full load voltage but no current is taken from the secondary, and this enables the power lost in the magnetic core of the transformer to be measured. As well a power, the tests also allow the inductances to be measured as well as the resistances, in order ot characterise the transformer fully.
How a transformer can be used as impedance matching?
If the line impedance is Z0 and the load is ZL then connect the load using a transformer with N turns ration. N=sqrt(Z0/ZL)
With aid of diagram explain why magnetic flux of transformer remains almost constant from no-load to full load?
since the volt amphere turns in secondary neautralises the primary voltamphere turns making the magnetic flux in the core remain constant
What is the percentage of the no-load current in a transformer to its full load current?
2 to 5% of full load current
What is voltage regulation of Transformer?
The change in output voltage from no load to full load defines the voltage regulation of that transformer.
Why noload current in big motors is higher than load current?
That is not always true.
What is load test on single phase transformer?
A load test on a transformer is done to make sure it stays within its designed temperature range while on full load.
What is full load magnetising current of transformer?
is it primary current ?
What do you mean by no load of transformer?
Transformers voltage ratings are typically at full load. For instance, A 24 VAC, 10A transformer will have a terminal voltage of 24 when it is feeding 10 amps to a load. Since the transformer windings have some resistance, the transformer designer has to wind the transformer to put out more than 24 volts, since some of the voltage will be lost, dropped across the resistance of the secondary windings. But, according to Ohm's law, the voltage dropped across a resistance is proportional to the current (E=IR). If we take away the 10A load, there is no current, and therefore no winding voltage drop! The excess voltage the designer built in now appears at the terminals. This is the no-load voltage. In my example above, when we remove the 10A load, the output voltage of the transformer might rise to 26.4V. We would say the no-load voltage of that transformer is 26.4V The ratio of full-load voltage to no-load voltage is called the transformer's "regulation factor". It is calculated as: (no-load voltage - full-load voltage) / full-load voltage * 100. Ours is: ((26.4 - 24) / 24) * 100 = 10%.
What is the no load current of 1600 kva transformer?
No load current depends on the design of the transformer, and what voltage it is energized at. It will typically be below 1% of full load, and can be significantly below 1% for utility sized transformers.
What do you understand by regulation in a transformer?
Regulation of transformer means percentage reduction of transformer secondary voltage due to transformer loading as compared to its no load voltage.Another AnswerA transformer's voltage regulation is defined as 'the change in its secondary voltage, from no-load to full-load, at a specified power factor, expressed as a percentage of its full-load voltage, with the primary supply voltage held constant'.
How do you find out no load and full load losses of Power Transformer?
By performing no load and short circuit tests. These are outlined in ANSII and IEEE literature.
Is a transformer load inductive or capacitive?
A transformer is fundamentally a set of coils; therefore, a transformer is an inductive load. However, by "transformer load", you seem to mean "the load that is connected to a transformer". Whether that load is inductive or capacitive depends mostly on what is hooked up to the transformer.
How much current does a three phase 11kv 50kva transformer draw per phase no load and fully loaded and is there any significant loss in the average delta star transformer?
Fully loaded - 2.62 amps at 11kV. The no load depends on the transformer design, but it will usually be significantly less than the full load amps (not sure on this size, but on larger transformers it is typically ~.05 - .1% full load, so you'd be looking at ~2.5 mA RMS). The connection type is not important. Transformers are very efficient, thus there is not a whole lot of loss in the "average" transformer. The actual loss will depend on the design criteria of the transformer.
Difference between off load transformer and on load transformer?
Hope this helpsAn "OFF-Load tap transformer" can only have it's tap adjusted when it is De-energized,while the "On-Load tap transformer" can adjust its tap under load conditions.Kind RegardsHammad KhanUniversity of Western AustraliaAnswerAn 'off load' transformer is one whose secondary is open circuited, and not supplying a load. An 'on load' (not 'load') transformer is one that is connected to a load.
