0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is trowel?
It is a small hand tool with a curved blade used by gardeners for planting. It is also a hand tool, with a flat blade, for scooping or spreading plaster
How do you figure a 7 foot horizontal rolling offset?
A rolling offset is generally an offset requiring a change in 2 directions. Eg. A horizontal offset and a vertical change in elevation. There is additional information required to answer the question. What is the angle of the fittings being used for offset? 15 deg. 30. 45? What is the change in elevation? If this is a flat (no change in elevation offset) using 45 deg., the offset dimension (7') is multiplied by 1.4142 which is the secant and cosecant of 45 deg. The result 7 ' x 1.4142 = 9'-10 13/16" Again, this result is for a flat run of pipe. If we have a rolling offset with a change in elevation of say 1'. We can use the Pythagorean theorem (A2 +B2 = C2) The result would be (1')2 + (9'-10 13/16")2 = 98.99812 sq. ft. The square root of 98.99812 is 9'-11 3/8"
Which steel is expensive hot rolled or cold rolled?
It takes much more energy to roll a sheet of metal in cold rolling than it does for hot rolling. Heating up a sheet of metal makes the material more malleable, so when it is rolled between two rollers, it can form into a flat sheet much easier. A cold sheet of metal that is not heated up will be put through the rollers and have a higher amount of energy needed to push it through. Though there is less heating required, this is balanced out by the fact that it must be pushed through with more energy.The cold rolling process is an expensive one, especially compared to the process of hot rolling sheet metal. For example, since cold rolling requires that workers frequently clean parts like the rollers, cold rolling has extra costs for any supplies needed to clean the parts, downtime while the parts are being cleaned and labor costs for the worker who does the cleaning. Also, the additional energy needed in the cold rolling process adds cost to the final product. call me if u need more: 0784971498
Why would a flat roof be better than a sloped roof?
A flat roof would be better than a sloped roof because a flat roof is significantly cheaper to build. Another consideration of a flat roof would be that it is a more modern design and would fit a more contemporary home.
In flat rolling what is a screw down and a top roll balancing mechanism?
In a rolling mill, the screw down (usually electrically operated in big mills) is the mechanism for setting up the spacing between the rollers, called the roll gap. The top roll balancing mechanism is a mechanical (rods, springs) or hydraulic setup to hold the top roller up in contact with the screw down. The larger mills we see in operation have massive rollers, and they have considerable weight. The whole of the upper roll mechanism will be set in heavy chocks to to stabilize it and distribute the loads of the rolling operation. Additionally, we often see mills with backup rollers, and the top work roller and backup roller pair will be held in contact with the screw down by the top roll balancing mechanism. There is a bit more to this when we consider the dynamic operation of the biggest rolling mills, but the basics remain the same. The thickness of the product, the "indexing" of the roll gap, will be set by the screw down. And the the top roller is held up against the screw down by the top roll balancing mechanism.
What is a rolling pin?
utensil consisting of a cylinder (usually of wood) with a handle at each end; used to roll out doughA ROLLING PIN IS USED IN BAKING TO FLATTEN OUT BISCUIT DOUGH, COOKIE DOUGH, OR ANY OTHER DOUGH THAT REQUIRES SPREADING OUT FLAT.
Is the land in usa flat or rolling land?
It is flat, rolling, mountainous, forested, deserted, and totally different everywhere,
What is a flat wire rolling mill and its benefits?
Flat rolling is the most basic form of rolling with the starting and ending material having a rectangular cross-section. The material is fed in between two rollers, called working rolls, that rotate in opposite directions.
Is a cylinder a flat faced solid or a rolling solid?
It is a flat-faced solid.
What if a flat or gently rolling land?
a plain
What is a large area of a flat or gently rolling land?
A large area of flat land or gently rolling land is a bay... There's the answer!!
Regions of flat or gently rolling land?
Regions of flat or gently rolling land are called plains. They are usually covered in grass and have small amounts of trees.
The rolling plains subregion being completely flat makes it?
a flat place in texas....?
What are flat gently rolling hills called?
plains
How do you make flat thread rolling die?
easy
Landform of flat or gently rolling land with low relief?
A plain is a landform of flat or gently rolling land with low relief. It is one of the Earth's major landforms.
What is in low-lying stretch of flat or gently rolling land in the cental part of the US?
The flat of gently rolling land in the central US is called the Great Plains.
