There are more than three amplifiers in a typical radio receiver.
If, however, you are asking why there are three "stages" in the IF section, then the reason is that the IF section of a typical superhetrodyne receiver needs more bandwidth than can normally be provided by a single stage. As a result, there are usually three stages, each tuned slightly apart, so that you get a reasonable bandpass - otherwise, the demodulated signal will suffer.
Radio Frequency is a wireless technology consisting of a transmitter and receiver tuned to the same frequency
To change the frequency on a radio controller car, you change the crystal in the transmitter and receiver.
It's a junction gate field effect transistor that has it's bandwidth tuned to operate (amplify) in the radio frequency range.
A radio receiver is an electronic device that receives radio wave/signal and convert the information carried by them to a usuable form through speaker. The principal functions of a radio receiver are frequency selection, amplification and detection of signals which are been convert back to its original form through the help of radio speaker.
That's not exactly true. Any frequency you choose has several radio stations on it,but just not in the same city.Frequency is what your radio uses to separate the individual stations. If two stationsin the same city transmitted on the same frequency, your radio couldn't separate them.When you tuned to that frequency, you'd hear both of them at the same time, and youcouldn't understand either one.Listen to the 27 MHz 'Citizen's Band' some time.
The AC frequency to which the circuits in the radio receiver must be tuned in order to concentrate on that particular station and ignore all the others.
Steve C. Cripps has written: 'RF power amplifiers for wireless communications' -- subject(s): Amplifiers, Radio frequency, Power amplifiers, Radio frequency Amplifiers
Assuming that the receiver uses a high-side local oscillator and an IF of 455 KHz, the image frequency is 910 KHz above. When tuned to 1600 KHz, the image frequency would be 2,510 KHz.
Norm Dye has written: 'Radio frequency transistors' -- subject(s): Power transistors, Radio frequency Amplifiers, Transistor amplifiers, Transistor radio transmitters
Stagger Tuned Amplifiers are used to improve the overall frequency response of tuned Amplifiers. Stagger tuned Amplifiers are usually designed so that the overall response exhibits maximal flatness around the centre frequency.It needs a number of tuned circuit operating in union. The overall frequency response of a Stagger tuned amplifier is obtained by adding the induvidual response together. Since the resonant Frequencies of different tuned circuits are displaced or staggered, they are referred as STAGGER TUNED AMPLIFIER.The main advantage of stagger tuned amplifier is INCREASED BANDWIDTH. Its Drawback is Reduced Selectivity and critical tuning of many tank circuits. They are used in RF amplifier stage in Radio Receivers.
Radio Frequency is a wireless technology consisting of a transmitter and receiver tuned to the same frequency
Advantages of a Tuned Radio Frequency (TRF) receiver include simplicity in design, lower cost compared to superheterodyne receivers, and high selectivity for tuning in to specific radio frequencies. Additionally, TRF receivers can be easily modified and customized for specific applications or requirements.
I would very much like to see you with greater frequency. What frequency will you be on? I can switch to another radio station by adjusting the frequency of my radio receiver.
To change the frequency on a radio controller car, you change the crystal in the transmitter and receiver.
A signal from a radio station is tuned in a radio receiver by applying the signal to a resonant tuned circuit that accepts the wanted signal while rejecting all the other signals arriving.
radio frequency amplifier intermediate frequency( If strip) in a superheterodyne radio mixer /demodulator Audio amplifier
The superheterodyne converts the desired incoming signal frequency to an (usually lower) intermediate frequency before demodulating it and extracting the audio signal (or video/data, etc).The neutrodyne is a tuned radio frequency design where all amplifying stages operate at the incoming signal frequency. This was the commonest design up to the 1930s. The triode amplifiers used suffered from signal feedback, where a signal from the amplifier's output was coupled back to its input. This could cause the amplifier to act like a transmitter and to oscillate. Neutralization (with capacitors) was invented to prevent this problem and the circuit was named the "neutrodyne".