0
. Which type of full-wave rectifier has the greater output voltage for the same input voltage and transformers turn ratio?
Wiki User
∙ 9y ago
well when you see on basis of output voltage the centre tapped Transformers is .
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Why an op-amp diode rectifier called as a precision rectifier?
In a rectifier made of just diodes, the diodes have a voltage drop, resulting in a lower DC output voltage. By introducing an Op-amp, this voltage drop can be overcome. Since there is no voltage drop caused by the diodes, the rectified signal is not changed by the rectifier, so it is called a precision rectifier.
What happens to voltage in a step-down transformer?
The voltage induced into the secondary winding will be lower than the voltage applied to the primary winding. The primary winding being the winding connected to the supply, while the secondary winding is the one connected to the load.
What is voltage regulation of a rectifier?
A: actually a full wave rectifier does not regulate. It will however follow the input minus diodes voltage drops. depending on current it is assumed to be .6 to .7 volts for silicon diodes.
What circuitry converts an ac voltage into dc voltage?
either a rectifier or a motor generator
HOW do I SELECT A STEP DOWN TRANSFORMER?
By looking to the number of turns in the Primary and Secondary Coils. "A Step down transformers are designed to reduce electrical voltage. Their primary voltage is greater than their secondary voltage. This kind of transformer "steps down" the voltage applied to it."
Formula for peak inverse voltage?
piv:the maximum value of reverse voltage across a diode that occurs at the peak of the input cycle when the diode is reversed-biased.
How can capacitor smooth or reduce the ripple of the voltage produced by the rectifier?
when rectifier is on, the capacitor is almost transparent (it charges to the voltage provided from the rectifier) when rectifier is off, capacitor holds the peak voltage since it stored a charge during rectifier on time.
What are the Importance of of peak inverse voltage in rectifier service?
What are the Importance of of peak inverse voltage in rectifier
What device is also called a rectifier?
A rectifier is an electronic device that changes an AC voltage to a DC voltage.
Why an op-amp diode rectifier called as a precision rectifier?
In a rectifier made of just diodes, the diodes have a voltage drop, resulting in a lower DC output voltage. By introducing an Op-amp, this voltage drop can be overcome. Since there is no voltage drop caused by the diodes, the rectified signal is not changed by the rectifier, so it is called a precision rectifier.
How do rectifiers and transformers work in a PC power supply?
There is no transformer used in PC power supply. There is rectifier used to rectify or convert AC input voltage into DC output voltage.Transformer based rectifier produces some spikes at the output DC voltage, hencethey uses SMPS (Switch Mode Power Supply) to avoid spikes to the output DC voltage and get a smooth DC voltage.
What are the functions of current transformers and the difference between current transformers and voltage transformers?
To sense the current flow across the current transformers and to monitor the current ratings. In current transformers no voltage variations occurs. but in voltage transformers it is mainly used to increase or decrease the voltage value.
Which type of rectifier has the greatest output voltage for the same input voltage and trasformer turns ratio?
Bridge Rectifier
What is tha purpose of a rectifier assembly?
Are you referring to the Rectifier in the Alternator? Simply, a rectifier turns the AC voltage produced my the alternator to run the electrical components in your vehicle and turns it into DC voltage to recharge your battery.The purpose of rectifier assembly is to turn the AC voltage. This is in a car.
How do you increase a voltage?
If you are dealing with AC voltage, you can use a transformer. You can find transformers at places like Radio Shack, Jaycar and some online sites like eBay. Transformers have to be connected in the right way. You have to connect the voltage you are going to increase to the low voltage side and on the high voltage side will be the voltage which has been stepped up by the transformer. (If you want a DC voltage out, you will need to connect a bridge rectifier to the output, followed by a large capacitor and then a voltage regulator of the voltage you want out.) If you are dealing with DC voltage then you will need a chip to step the voltage up. These chips can step voltage up from around 1 to 10 volts to at least 20 to 30 volts. These chips also need to be connected correctly. You will need more components than using a transformer. You will probably need some capacitors and some resistors. Depending on the IC you choose, you will find many circuits on Google for it and how to build them. By far the easiest type of voltage to step up is AC. If you have the option of AC, and need to have a very high voltage output, you are better off using a transformer, bridge rectifier and a rectifier.
Where is the voltage rectifier on a 1985 Suzuki Gs300 L?
The voltage rectifier is on the left side of the motorcycle just in front of the rear tire.
What are the advantages of power transformers over voltage transformers?
Power transformers can be used for power transformation. Voltage transformers are not suitable for high power applications.
