0
What else can I help you with?
How do you remove an ignition switch that is jammed in the run position on a 1991 sunbird?
Never mind figured it out
What do you do if your 1991 Pontiac Bonneville will not shutt off after it is turned on?
replace the key switch hope this works for you
How do you fix the ignition switch that is going past the start position on a 1991 Mercury Cougar?
To fix the ignition switch on a 1991 Mercury Cougar that is going past the start position, first disconnect the battery to ensure safety. Remove the steering column cover to access the ignition switch, then inspect the switch for wear or misalignment. If necessary, adjust the switch position or replace it if it's damaged. Reassemble the column, reconnect the battery, and test the ignition to ensure it operates correctly.
Does the 1991 Chevy Silverado have an ACC position on the ignition switch?
Yes. After inserting the key, turn it counterclockwise one click.
Where is the torque converter switch located on a 1991 Pontiac sunbird?
On a 1991 Pontiac Sunbird, the torque converter switch is typically located on the transmission, often near the valve body or attached to the transmission control module. It may also be found on the throttle body in some configurations, as it works in conjunction with the engine's throttle position. For precise location details, it’s best to refer to the vehicle's service manual.
How do you wire a power window for a 1991 Honda accord?
To wire a power window for a 1991 Honda Accord, first, ensure you have the appropriate wiring harness and switch. Connect the window motor's two terminals to the power window switch; typically, one terminal connects to the switch's up position and the other to the down position. Then, attach the switch to a power source, usually the vehicle's battery, ensuring proper grounding. Finally, test the switch to ensure the window operates correctly in both directions.
Why don't the wipers in your 1991 Dodge Caravan turn off when the switch is in the off position?
Wiper motors have an internal switch that keeps the wipers running after you turn them off. The switch stays active until the wipers get to the "PARK" position and if the drivers wiper switch is off, then the wiper motor is turned off internally. I suspect the internal switch has failed. Unfortunately the switch cannot be easily replaced. Fortunately, wiper motors are not terribly expensive.
1991 caprice classic runs smooth idling but spits and sputters when you accelerate?
it could be a bad vacuum line or it could be the the throttle position switch
Where is the inertia switch on a 1991 Isuzu trooper?
According to the wiring diagram, there is no inertia switch. There is only a relay switch in a 1991 Isuzu Trooper.
What would cause the heater fan rear defroster to not work on a 1991 Chevy caprice the heater fan only works on the highest setting?
If the heater fan on your 1991 Caprice only works on "High" the problem is more than likely the resister assembly in your blower circuit or poor connections at the resister assembly. When the switch is in the "high" position the current does not flow through the resister assembly it flows directly to the coil of the blower relay. When the switch is in "low", "medium 1", or "medium 2" position the current flows through 1, 2, or all 3 of the resistors in the resistor assembly which results in the 3 different lower speeds. Check the resister assembly and replace if needed.
How do you take the ignition switch out of a 1991 lexus ls400?
To remove the ignition switch from a 1991 Lexus LS400, first disconnect the negative battery terminal to ensure safety. Next, remove the steering column covers by unscrewing the screws holding them in place. Once the covers are off, locate the ignition switch, detach the wiring harness, and unscrew the switch from its mounting position. Finally, carefully pull the ignition switch out of the steering column.
Where is the neutral safety switch in a 1991 Infiniti G20?
In a 1991 Infiniti G20, the neutral safety switch is typically located on the transmission. It is mounted on the transmission's side and is connected to the shift lever mechanism. This switch prevents the engine from starting unless the transmission is in the "Park" or "Neutral" position. To access it, you may need to lift the vehicle and remove any necessary undercarriage coverings.
