0
The name of the line for the compass alignment is the index line. The line and the numbers around the outside edge can be used to plot a course to a distant object.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
Does aligns exists?
1.It's aliens not aligns 2.We have no proof, but nothing is impossible
What is the different steps in bisecting a line?
1. first draw a line any measurements 2. then get your compass and place it on the left side of your line remembering that the compass has to be more than halfway open then go up to the middle with ur compass and draw one half of a cross with the compass then draw another half a cross below the line not changing the width of the compass but make sure it is in line with the other half cross now take the compass of your page now place the point on the other side of the line and do the same as i just said then you should get two crosses one above the line and one below the finishing touch is get a ruler and where the crosses meet draw a line strainght the way down and then your done i hope that helped i learnt it in a maths lesson
How do you draw a tangent to a circle from a point on its circumference?
Short instructions:Construct the diameter of the circle at the tangent point Construct a line at right angles to the diameter at the tangent point. this is a tangent to the circle at that point.Detailed instructions with compass and straight edge:Given: circle C with a point T on the circumference Sought: Tangent to C at TFind the center circle CPlace the needle of the compass on the (circumference of) circle C (anywhere), draw a circle [circle 1] (I think circle 1 has to be smaller than twice the diameter of circle C).Without changing the compass size, place the needle of the compass on the intersection of circles C and circle 1, draw a circle (circle 2)Without changing the compass size, place the needle of the compass on the other intersection of circles C and circle 1, draw a circle (circle 3)Connect the intersections of circle 1 and circle 2 (one is outside and one inside circle A) this we call [ line 1]Connect the intersections of circle 2 and circle 3 (also here one is outside and one inside C) [line 2]The intersection of line 1 and Line 2 is [O]. This is the center of circle CDraw a line [line 3] from [O] through [T] and beyondConstruct the diameter of the circle at [T] (the point for the tangent) and extend it beyond the circumference of circle C With your compass needle at [T] mark off equal distances on [line 3] inside and outside circle C. We call these points [4] & [5]Increase the compass size somewhat and with the needle at [4] draw a circle [circle 4]Without changing the compass draw [circle 5] centered on [5]Construct a line perpendicular to line 3 at [T]The line through the intersections of circle 4 and circle 5 is the sought tangent at [T]Note: although the instructions say "draw a circle" often it is sufficient to just mark a short arc of the circle at the appropriate place. This will keep the drawing cleaner and easier to interpret.
How do you represent root 2 on number line?
It is a number that is approximately equal to 1.4142. Since it is an irrational number, any decimal representation must be an approximation. However, if you have a pair of compasses, it is not that difficult to mark sqrt(2) on the number line.Draw a line at 1 that is vertical to the number line.Put the compass point at 1, radius = distance from 1 to 0 and draw an arc to cut the vertical line at X.Put the compass point at 0, radius = distance from 0 to X and draw an arc. This will cut the number line at sqrt(2).
How to draw 174 and name type of angle?
To draw an angle of 174 degrees, you can follow these steps: Draw a straight line using a ruler or straightedge. This will be one side of the angle. At one end of the line, use a compass to draw an arc of 174 degrees, making sure that the arc intersects the line you drew in step 1. Without changing the width of the compass, place the point of the compass at the other end of the line you drew in step 1, and draw another arc that intersects the first arc you drew in step 2. Draw a line connecting the endpoint of the line and the intersection point of the two arcs, creating the second side of the angle. Label the vertex of the angle with a capital letter. To name the angle, you can use the vertex letter and the endpoint letters, in that order, with the vertex letter in the middle. In this case, the angle could be named "angle BAC" or "angle CAB", depending on which endpoint you choose to name first. As for the type of angle, an angle of 174 degrees is an obtuse angle because it measures greater than 90 degrees but less than 180 degrees.
How can you construct a perpendicular bisector of a given segment using only two parallel edges of a straightedge with out usign any mesurements on the ruler and compass?
Do I have a compass to use or not ? It's not clear from your question, but since you mentioned it at the end of the question, I'll assume that I do have a compass, and in that case, I only need one straight-edge. 1). Plant the compass on one end of the line segment, open it to more than half the length of the segment, draw a long arc that crosses the segment. 2). Keep the same opening, pick up the compass. 3). Plant the compass on the other end of the segment, draw another long arc that crosses the segment. 4). Sell the compass. 5). The two arcs intersect at two points on opposite sides of the segment. With your straight edge, draw a line between these two points. That line is the perpendicular bisector of the original segment.
What is the ISBN of The Compass of Zen?
The ISBN of The Compass of Zen is 1-57062-329-5.
How do you divide a line into 3 equal parts using only a straight edge and a compass?
1. A given length of line is drawn from points A to B. 2. A compass is used to measure the line and construct an equalateral triangle using line A to B as the base side of the triangle. 3. Use the compass to bisect the two adjacent ventexs at the base of the triangle extending these lines till they intersect finding the center, point O, of the triangle. 4.Draw the solution finding line parallel to A to B through point O. Extend this line to intersect with the sides of the triangle at points C and D. 5. One third of line A to B is equal to line section A to C and line section B to D.
How do you weigh a drink can?
1. Open the can2. Drain the contents of the can completely (by drinking or discarding)3. Place the can on a scale/triple beam balance4. Measure the weight of the can by the weight displayed when the end aligns with the white line.
How do you line up the timing chain marks on a 2001 Saturn 2.2 engine?
Crankshaft dot should be at the 5 o'clock position. Intake camshaft sprocket should have the "INT" mark at approx. 2 o'clock. Exhaust camshaft sprocket should have the "EXH" mark at approx. 10 o'clock. Timing chain has 2 silver links and 1 copper link. Copper link aligns with the mark on the Intake cam sprocket, 1 silver link aligns with the mark on the Exhaust cam sprocket, and the other silver link aligns with the mark on the crankshaft sprocket.
Name of the power line issue can cause problems with your computer?
1.Line sag2.Line surge3.Line noise4.All of the above
Has at least 1 line of symmetry and name long?
parrallelogram
