WORKSHOP PROCEDURE
1. Open door.
2. Turn ignition 'ON'.
3. Operate front seat fully rearward for access.
4. The air recirculation switch should be in the fresh air mode.
5. Turn ignition 'OFF'.
6. Remove the glove compartment hinge retaining screws (Illustration 1).
7. Remove the glove compartment retaining screws (Illustration 2).
8. Disconnect the glove compartment lamp electrical connector (Illustration 3).
9. Remove the glove compartment.
10. Disconnect the air inlet blend door actuator electrical connector, undo and remove the climate control upper front stepper motor securing screws and displace the climate control stepper motor and reposition to gain working access (Illustration 4).
11. Remove the air inlet blend door actuator securing screws (Illustration 5).
12. Displace and remove actuator.
13. On all vehicles, align the actuator shaft as follows: Connect the air inlet blend door actuator to the electrical connector, and switch the ignition 'ON'. By a combination of operating the air recirculation button ON/OFF and disconnecting the electrical connector at the correct time set the shaft to the correct position. The flat opposite the curved face should be set nearest to and parallel with the line on the actuator body
Note: A DTC will be stored during the alignment procedure since the open circuit will be detected.
14. Turn ignition 'OFF'.
15. Ensure the air inlet blend door is in the fresh air position.
Caution: Care must be taken not to apply too much adhesive as this could be pushed backwards on the motor housing when inserted in the climate control unit.
16. Apply Super Glue Gel or a suitable locally sourced adhesive to the actuator shaft (Illustration 7).
Note: Do NOT apply adhesive to the end of the actuator shaft.
17. Align, install, and fully seat the actuator. Hold the actuator in position until the adhesive has set.
Note: Do NOT switch the ignition 'ON', or operate the air recirculation switch until ten minutes have elapsed to allow the adhesive to set.
18. Install and tighten actuator-securing screws.
19. Connect actuator electrical connector.
20. Reposition and install the climate control upper front stepper motor.
21. Install and tighten the climate control upper front stepper motor securing screws.
22. Install the glove compartment.
23. Connect the glove compartment lamp electrical connector.
24. Install and tighten the glove compartment retaining screws.
25. Install and tighten the glove compartment hinge retaining screws.
26. Turn ignition 'ON'.
27. Operate front seat to original position.
28. Turn ignition 'OFF'.
29. Position WDS alongside vehicle, switch 'ON' Portable Test Unit (PTU) and allow software to load.
Note: During previous operation, Connect PTU to vehicle via diagnostic cable.
30. Clear DTCs, switch OFF PTU, disconnect and return WDS to original location.
31. Close door.
How do you remove the interior panel containing the rear woofer in a 2002 jaguar xk8 coupe? thanks
try a four loco at your neighbor hood store.
The curb weight for a 2002 Jaguar X-Type is 3400 to 3500 pounds. The 2002 Jaguar X-Type is 183.9 inches long.
Could you display indicator dashboard icons for jaguar x type 2002?
In 2002 Ford Motor Company owned Jaguar motor company, so technically 100 percent of the parts are four parts. The Jaguar was manufactured in England using parts specifically created for Jaguar.
where is the oxygen knock sensor located on a 3000 v6 Jaguar engine 2002 model and how can i change it?
Check the fuse for the interior lights. Nick
Jaguar XKR 2002 has a V8 4.0 litre engine with double compressors which produces 370 BHP. Its limited to 250 kph.
To replace an alternator on a 2002 Jaguar van den plas 4.0 simply refer to the user manual.
FPS Interior Belgium was created in 2002.
XO Interior Systems was created in 2002.
R134a