0
That could work, because there does no 4 ohm amplifier exist. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout << Zin. The damping factor Df = Zin / Zout tells you what Zout is. Zout = Zin/Df. If the damping factor Df = 200 and the loudspeaker impedance is Zin = 4 ohms, the output impedance of the amplifier is Zout = 4 / 200 = 0.02 ohms. You see, there is no "4 ohm amplifier" with a 4 ohm output. Scroll down to related links and look at "Voltage Bridging - Zout < Zin".
What else can I help you with?
I HAVE A crunch 1000.1 AMP THAT im trying to push 1 punch p3 15 subwoofer how do i wire it?
If youre running a single woofer get the dual 2 ohm woofer. Wire them parallel, which will bring it down to 1 ohm when you put it on the amp. 1 ohm will pull the most power from the amp
Can you wire a dvc 2 ohm sub woofer to a dvc 4 ohm sub woofer?
You can, but you may damage your amp. If you wire them in parallel (both wires from each connected to the amp) then you will have an effective resistance less than 2 ohms. If you wire them in series then you will have an effective resistance of 6 ohms. Resistance that is too low draws more power than the output is rated for. Resistance that is too high reduces the volume and may distort the sound.
Can you wire a 4 ohm 500 watt sub woofer in parallel with a 4 ohm resistor to get 300 watts out of your 75 x 2 bridged amp would this effect sound quality what wattage of resistor?
This would have 2 effects:Cause an impedance mismatch between the amp and the speaker.Draw more current from the amp, possibly overloading & damaging it.Neither is desirable.
Can you hook up a 4ohms sub and a 2ohms sub to the same amplifier?
ONLY if your amp can pull a 2 ohm load! Which is vary few but your more expensive amp can pull 1/2 ohm load
Can you connect 2 amps to run a subwoofer?
If your sub is 2 ohms and your amp is 2 ohm stable, your done. Your amp will be at 2 ohms because the sub is 2 ohms.
How do you know what kind of subwoofer goes with what amp?
a 500 watt sub woofer puts out 250 RMS a 500 watt amp puts out the same and if you want a good setup get a sub with RMS and a amp with 1200 max so 600 RMS will be powering the same 500 RMS sub woofer then you can tune it to push the sub woofer a bit and the sub woofer should take it I recommend ether mono single channel 2 channel brands go name brand if u want support later or go no name to be different
How would you hook up 2 8 ohm woofers with a 4 ohm dual voice coil woofer?
You could with a 4 channel amp. Bridge it to two channels and hook up the two 8 ohm woofers in parallel on the one bridged channel. Then hook the two coils on the dual coil woofer in series with the other bridged channel on the amp.
Why buy an 8 ohm sub?
I have recently purchased 2 10" Kicker Comp 8-ohm subs for the simple reason that I already had an amp that matched the power rating for the subs at a 4-ohm load (amps rating). The amp will put out about 800w @ 2-ohm and 400w @ 4-ohm load (rms values). By running 2 single voice coil 8-ohm subs wired in parallel you are effectively cutting the impedance in half (8 + 8 = 4-ohm in parallel). To do this you simply connect the positive terminal of one sub to the positive of the other sub and then to the positive of the speaker output on the amp. Same with the negatives, sub to sub then to amp. Had I purchased the more common 4-ohm single voice coil subs my load to the amp would have been 2-ohms and too much power would be getting to the subs (100 watts more rms power than the peak power the subs could handle). I did this because of the space I had available and also because the Kicker Comp has performed well for me in the past as an entry-level woofer. Hope this helps!
How do you wire 2 8 ohm subwoofers to a 4 ohm amp?
Hook all the negatives together, and hook all the positives together. you would have 2 wires for each. one from the amp to the first sub, and another going from the first sub to the second.
Set up 2 4 ohm sub to 2 ohm?
If you are trying to pump a 2.4 ohm sub with a 2 ohm rated amplifier you should be fine. The rating on the amplifier is the least resistance it should have on its load. Anything less than 2 ohms would fry your amp.
Will 8 ohm sub woofers work with a 4 ohm amp?
if you put 2, 8 ohm speakers together on the same channel you will trick the amp into seeing a 4 ohm load, it is not advisable to run a 8 ohm coiled speaker on a 4 ohm amp unless you do the above. So if you want to run 2 8 ohm speakers from a 4 ohm amp this will work the best although the amp will need to be hefty as its worse to underpower a sub than overpower it! I have used a 8 ohm speaker myself on a car amp and had no problems but it was not a cheap entry level amp! some amps will take it, others will get hot and enter protection mode. Hope this helps!!!
1000watt rms 2 ohm 15inch subwoofer what would be the best wattage amplifier to pair with this and would it have to be 2 ohm aswell?
is it duel 2 ohm or duel 4 ohm or just a singel 2 ohm sub??? you can run anything from a 1 ohm amp to a 2 ohm amp just depending if you want to add another sub later if your wanting to add 1 later get 1 big enough to run 2 subs so you wount be wasting your money on sumthing you dont need say 5 months from now
