0
What else can I help you with?
How do you wire up a dual 4 ohm sub to 2 ohms?
i dont now
Can you hook up a 4ohms sub and a 2ohms sub to the same amplifier?
ONLY if your amp can pull a 2 ohm load! Which is vary few but your more expensive amp can pull 1/2 ohm load
Can you have a 2 ohm sub with a 4 ohm sub?
Yes, you can have a 2 ohm subwoofer and a 4 ohm subwoofer in the same system. However, it is important to match the impedance to avoid damaging your amplifier. You can wire them in series or parallel to achieve a compatible overall impedance for your amplifier.
What is difference between 2 ohm and 4 ohm sub-woofers?
It is the impedence (coil resistence)normally sub component (drivers)are in 8 ohms impedence.2 in parralel is 4 ohms and 4 in parralel makes it 2 ohms.
1000watt rms 2 ohm 15inch subwoofer what would be the best wattage amplifier to pair with this and would it have to be 2 ohm aswell?
is it duel 2 ohm or duel 4 ohm or just a singel 2 ohm sub??? you can run anything from a 1 ohm amp to a 2 ohm amp just depending if you want to add another sub later if your wanting to add 1 later get 1 big enough to run 2 subs so you wount be wasting your money on sumthing you dont need say 5 months from now
Can you connect 2 amps to run a subwoofer?
If your sub is 2 ohms and your amp is 2 ohm stable, your done. Your amp will be at 2 ohms because the sub is 2 ohms.
How do you wire 2 8 ohm subwoofers to a 4 ohm amp?
Hook all the negatives together, and hook all the positives together. you would have 2 wires for each. one from the amp to the first sub, and another going from the first sub to the second.
Wire 2 dvc 4ohm subs to 2 channel Amp-sub400rms4ohm amp 350x24 ohm rms 700x22 ohm rms 1400x1 4 ohm peak power Best way to set up?
This question makes little sense. Could you say what model amp it is? With two 4 ohm subs, you can either do 1 ohm or 4 ohm. Now if you have a bridgeable two channel, I think you can do a 2 ohm load. For a 4 ohm load, two 4 ohm subs, connect both positives from one side of the subs to the positive out. Then the negative coils from the opposite side (other side of the sub) to the negative output. Then connect the remaining negative and positive together on each subs. Look here http://www.the12volt.com/caraudio/woofer_configurations.asp
If you have a 1000 watt 2 ch amp and 2 1000 watt G A 12's how do you set it to 1 ohm?
unfortionatly it alot more difficult than that. you first need to know if your subs are dual or single voice coil. then the ohm of the coils. your next step is to make SURE your amp is one ohm stable. (most are not) if your sub ohm will match you amp ohm. safely. its all in the wireing of the amp to the subs to change the ohms. if you dont know exactly how to wire them DONT DO IT yourself.
Where can you buy a smd subwoofer?
wccaraudio.com Can also pick up DD1 and has links to various items that Steve Meade uses for his builds (xs power batteries and the like) PRICES: dual 2 or dual 1 ohm 15" sub: 849.99 dual 2 or dual 1 ohm 18" sub: 899.99 SMD distortion detector: 149.99 (Extreme Backorder, long wait)
Can you replace subwoofer in 2000 Chevy Tahoe with aftermarket subwoofer?
Your SUV comes with a 8" subwoofer from the factory. Most likely a 4-ohm sub. I know the Kicker Comp VT 8" will bolt right in and you can get them either 2-ohm or 4-ohm. You would probably notice quite a difference putting a 2-ohm in.
Will 8 ohm sub woofers work with a 4 ohm amp?
if you put 2, 8 ohm speakers together on the same channel you will trick the amp into seeing a 4 ohm load, it is not advisable to run a 8 ohm coiled speaker on a 4 ohm amp unless you do the above. So if you want to run 2 8 ohm speakers from a 4 ohm amp this will work the best although the amp will need to be hefty as its worse to underpower a sub than overpower it! I have used a 8 ohm speaker myself on a car amp and had no problems but it was not a cheap entry level amp! some amps will take it, others will get hot and enter protection mode. Hope this helps!!!
