0
A 2-in schedule 40 sheets pipe is used as a leg for a machine The Load carried by the leg is 2350lb.Compute the bearing stress on the floor if the pipe is left open at its end?
Wiki User
∙ 14y ago
A. A 2-in schedule 40 sheets pipe is used as a leg for a machine. The Load carried by the leg is 2350lb. a. Compute the bearing stress on the floor if the pipe is left open at its end b. Compute the bearing stress on the floor if a flat plate is welded to the bottom of the pipe having a diameter of the pipe
Wiki User
∙ 14y ago
Wiki User
∙ 14y agoA. A 2-in schedule 40 sheets pipe is used as a leg for a machine. The Load carried by the leg is 2350lb.
a. Compute the bearing stress on the floor if the pipe is left open at its end
b. Compute the bearing stress on the floor if a flat plate is welded to the bottom of the pipe having a diameter of the pipe
Add your answer:
Earn +20 pts
What is shaft bearing?
A shaft bearing is a low friction support device for a rotating member of a mechanical machine.
Is Number and variety of machines in the shop relevant to job shop scheduling?
Yes. Obviously, you have to tailor the schedule to the resources available, both human and machine, or you need to change those resources if the schedule cannot be changed.
Why does washing machine leak from the bottom?
The most likely cause of a washing machine leak is a small hole in the rubber door seal which can be easily replaced.As a temporary measure the seal can be loosened and twisted 180degrees until the top is at the bottom. Probably a bad tub bearing. Live with it, or get a new machine. +++ It won't be the bearing because the shaft is outside of the drum, but it could be a leak on one of the pipe joints, or (as happened on mine) on the pump, which does use a shaft running through a bush and seal from the inside to the outside of the pump body.
How long does it take to cut 3 schedule 160 pipe?
depends on how you cut it and the size of the pipe, but with a machine blade, it shouldn't take more than couple minutes
How many programming language does Ada Lovelace developed?
None. Ada Lovelace is credited with creating the first algorithm intended to be carried out by a machine but she did not develop any programming languages. She died in 1852, a Century before machines were even capable of translating high-level code into machine code.
A 2-in schedule 40 sheets pipe is used as a leg for a machine The Load carried by the leg is 2350lb?
mechanical engineering
What type of jobs or operations can be carried out on a pillar drilling machine?
. Lists the operation which can be carried out by using a pillar drilling machine.
A auger bearing for a 1977 sears 5 HP snowblower?
pull or press the bearing out and take to a local bearing/machine shop to measure
What is shaft bearing?
A shaft bearing is a low friction support device for a rotating member of a mechanical machine.
Did only officers get machine guns in World War 2?
No, machine guns were typically carried by a machine gun team. An officer seldom carried a machine gun and normally a pistol and perhaps a carbine. Some may have been able to get a sub-machine gun.
How do you remove cam bearing on 4.3 L engine?
You either need a camshaft bearing installer/remover. Or just take the block to your local machine shop..
How do you remove wheel bearing escourt 98 si?
Take the steering hub and knuckle to a machine shop. The bearing must be pressed out and a new one pressed into the hub.
How do you remove the front wheel hub and bearing from a 1989 Ford Tempo FWD?
you need to remove the entire steering knuckle and have a machine shop press out the hub and bearing for you.
How do you replace bearing caps on a 350 are they all the same i lost a bearing cap can i use any bearing cap from any 350?
You can purchase new or used bearing caps, but there is machine work required. If you are talking about main bearing caps, the block will need to be line bored with the new cap in place. If you're talking about a connecting rod bearing cap, the rod will need to be resized with the new bearing cap in place.
What is a hard bearing and a soft bearing What is the difference between them?
There are two primary types of balancing machines, these are hard-bearing and soft-bearing machines. The difference between them, is in the shaft / bearing suspension and not the bearings. In a hard-bearing machine, balancing when preformed is done at a frequency that is lower than the resonance frequency of the machine suspension. In a soft-bearing machine, balancing when preformed is done at a frequency higher than the resonance frequency. Both types of machines have various advantages / disadvantages. Hard-bearing machines are generally more versatile and can handle pieces with greatly varying weights and because hard-bearing machines are measuring centrifugal forces this then only require one-time calibration. Only five geometric dimensions need to be fed into the measuring unit to be ready for use. Therefore, ideal for low- and middle-size volume production and in repair workshops. Soft-bearing machines are not so versatile with respect to amount of rotor weight to be balanced. Preparation of a soft-bearing machine, individual rotor types is more time consuming and needs calibration for every individual part. It is very suitable for high-production volume and high-precision balancing tasks. Both types hard and soft-bearing machines can be automated to remove weight automatically, example such as by drilling or milling. Hard bearing machines are generally more robust and reliable. Both machine types can be integrated into a production line and loaded by a robot arm or gantry, requiring very little human control.
What are examples in machinery of things that are very tight?
Spindle and bearing assembly, Different shafts and bearing assembly, Spindle and pulley assembly, bed and leg assembly, machine and motor assembly.
What is an amperage?
An amperage is the electric current's strength carried by a conductor or machine generated as measured in amperes.
