0
A 3 Volt battery sends a current of 0.10 A through a light bulb what is the resistance of the filament of the bulb?
Wiki User
∙ 14y ago
Volt (V) = Resistance (R) times Current (I)
therefor
R = V / I
30 Ω = 3V / 0.1A
Wiki User
∙ 14y ago
Tarun ganvit
R=v÷I
R=3÷0.10
R=30
Add your answer:
Earn +20 pts
If a toy car with a resistance of 2 ohms is connected to a 3v battery how much current flows through the car?
Ohm's Law: V = IR (voltage = current times resistance).Ohm's Law: V = IR (voltage = current times resistance).Ohm's Law: V = IR (voltage = current times resistance).Ohm's Law: V = IR (voltage = current times resistance).
Does the glow of bulb depend on current or voltage?
Since the bulb has a constant resistance, increasing the voltage will increase the current which will increase the brightness until the bulb blows in a flash of light.Ohm's Law governs this process where Volts = Current x Resistance.Another Answer Incandescent lamps do not have a constant resistance, as their resistance increases significantly with temperature. In fact, the 'hot resistance' of a lamp filament is around 10-18 times higher than its 'cold resistance'. The temperature increase, of course, is due to the current passing through the filament. This means incandescent lamps do notobey Ohm's Law and are, thus described as being 'non-ohmic' or 'non-linear'. However, to answer your question directly, the rated power of a lamp only occurs at the lamp's ratedvoltage. Even a small reduction in voltage will result in a significant loss of power and, thus, brightness. So, in this sense, a lamp's brightness is determined by the voltage applied across its filament.
How will you describe the graph of resistance against current?
If resistance is high that time the current flow is low. Bcoz current always flow through the low resistance path.
Why tungsten filament does not obey ohm's law?
A tungsten filament does follow Ohm's Law at any instant of time. You may be confused in that the filament resistance changes from its "cold" state to its "hot" state. When cold the resistance is about 1/15 the resistance of what it is when the filament heats up, which happens very quickly. At any instant Ohm's Law holds. When the voltage is applied you have an initial current draw that exceeds the steady state current draw based on the change in resistance.AnswerOhm's Law either applies, or it does not. It cannot apply 'at an instant of time' -a change in current is either proportional to a change in voltage, or it isn't!A tungsten filament does not obey Ohm's Law, because the current flowing through the filament does not increase in proportion to the applied voltage. This is because the resistance changes due to the filament's increasing temperature as the applied voltage increases. This is why Ohm's Law specifies that current is proportional to voltage, provided the temperature remains constant.Although tungsten doesn't obey Ohm's Law, the so-called Ohm's Law equation applies whether a circuit obeys Ohm's Law or not. This is because the formula is really derived from the definition of the ohm, and not from Ohm's Law itself, which makes absolutely NO reference to resistance!
If a 9volt battery produces a current of 3amps through a load the resistance of the load is?
3 ohms. 9 volts across a 3 ohm resistor becomes 9/3 or 3 amps.
When the bulb is the resistance what this tells about the resistance?
An incandescent bulb has a filament that has a resistance. The value of the resistance determines the current that will flow for a given supply voltage. The heat generated by the current flowing through the filament gives off light. As the resistance of the filament decreases the current increases and you get more light.
What was a resistance invention?
The incandescent light bulb. The tungsten filament lights due to it's resistance of the current flowing through it.
What happens when a battery light the light bulb?
When the switch is turned it completes an electrical circuit. The circuit amperage flows through a high resistance filament in the bulb and it starts to glow. The bright glow from the filament and the reflector behind the bulb is what creates the flashlights beam.
Why is the filament inside an electric lamp made very fine?
The filament is fine so that its electrical resistance can be quite high. It is also long, for the same reason. Usually it is coiled up to fit the length in the lamp. The heating effect of electric current is proportional to the current squared, time the resistance (I*I*R). Most of the effect is due to the current. The current through the filament must be limited to stop it melting. Adding resistance will do that. Taking resistance away increases heating. So, a low energy lamp has a very thin filament and a high energy lamp will have a thicker filament.
A resistance of 10 ohms is placed across a 9 volt battery what current flows through the battery?
No current flows through the battery. There is a current through the external circuit. I = E/R = 9/10 = 0.9 amperes.
Do light bulbs use more energy over time?
An incandescent light bulb is essentially a wire through which current flows. The wire gets heated up and glows giving off light. According to Ohm's Law Volts = Current x Resistance. In this case resistance is the resistance of the filament. Since in a residence the voltage remains more or less constant, the way more energy would be use is if more current passed through the filament. If the resistance of the filament decreased then the current would increase. Not sure how an aging bulb would have a decreased resistance. If this were somehow possible such that the composition of the filament changes and reduced resistance then the energy required to operate the bulb would increase.
Why does the light bulb not work when the filament is broken?
A light bulb works by passing an electric current through the filament, which is usually made from a high resistance substance such as tungsten. When the current flows through, the filament glows which produces the light. When it burns out, no electricity passes and no glowing occurs. Source: i just know
Why does the resistance of a filament bulb depend on the current in the bulb?
The resistance of a piece of wire changes with temperature. In a filament bulb the wire is heated to about 3000 degrees C so a large change in resistance can be expected. A 240 v 105 w halogen bulb has a cold resistance of 35 ohms, but when running its resistance is 549 ohms.
What will happen if you connect a battery to a small light bulb with a single wire?
Nothing will happen. It requires two wires to complete the circuit. Electrical current travels from the battery terminal through the wire to a metal portion of the base of the lightbulb. The current then travels up through the filament wire which glows as the current travels through. The current then travels back down the other side of the filament wire to the base of the bulb and thus through the second wire back to source, which is the battery.
Is a light bulb a soure of light?
Yes, a light bulb is a source of light. When current is going through the filament the resistance generates enough heat that the filament glows, producing light.
A wire with resistance R is connected to the terminals of a 30 V battery. What is the current through the wire if the wire has the resistance?
Your current will be 30/R Amps. Where R is the resistance in Ohms.
Why does a light bulb filament get hot when electric current flows through it?
That is the result of resistance in the wire. In energy terms, some of the energy in the electric current is converted into heat.
