answersLogoWhite

0

Can a oven with below spec Voltage - 400V 3 phase Amperage - 20 AMPS 50/60 HZ Max input - 8200 watts Operate on 440V?

Can a oven with below spec Voltage - 400V 3 phase Amperage - 20 AMPS 50/60 HZ Max input - 8200 watts Operate on 440V?

User Avatar

povli

Lvl 1
1y ago
Updated: 9/20/2023

yes it can

What else can I help you with?

Related Questions

What is amperage input of transformer on 208 3 phase?

The amperage input of a transformer on a 208V three-phase system can be calculated using the formula: Amperage (A) = Power (Watts) / (Voltage (V) x √3). To determine the amperage, you need to know the power rating of the transformer in watts (or kilowatts). Once you have that, you can plug the values into the formula to find the input amperage.


What runs on 7 to 10 volts of electricity?

Some small electric motors will operate with an input voltage of 10 volts or less. Some bulbs for vehicles will operate on < 10 volts (but less bright than they would operate at their normal 12 volt input voltage.


How much lm317t ic can bear voltages?

The LM317 voltage regulator can be set to any output voltage from 1.2 V to 37 V. You must keep the input voltage between the maximum input voltage and the drop-out voltage for proper operation. The maximum input voltage the LM317 is guaranteed to bear is 40 V. The LM317 is guaranteed to operate when the input voltage is at least 3 volts above the set output voltage.


Can a 1H75 be used with 277V?

No, a 1H75 ballast is designed for 120V input voltage. You would need a ballast specifically rated for 277V to operate fixtures at that voltage safely and effectively. It is important to match the input voltage of the ballast with the fixture’s voltage requirements to avoid damage or safety hazards.


What size transformer do i need for a dazor floating fixture model?

The sizing of transformers without knowing the input supply voltage and output fixture voltage can not be done. Also needed is the amperage of the floating fixture.


What size fuse should be used for 2 amp power supply?

If the 2 amps is the output amperage of the power supply, the maximum that should be drawn from the unit is 2 amps. The load amperage that is connected to the power supply should govern the amperage of the fuse used. There is not much range there, the fusing could go from .25 to 2 amps. If the input amperage is 2 amps then the input and output voltage of the power supply should be stated.


Can you use a power adapter that has less amp input?

The rule with power adapters is generally that the voltage must be the same as the device's input voltage requirements. However, the amperage just has to be equal to or greater than the device's input current requirements. The device will draw as much current as it needs. But, mismatching voltages can destroy electronic equipment.


What size wire feeder should be used for 300 amps welding machine?

Usually the rating of a welding machine is expressed on the DC output side. What you need to state is what the input in voltage and amperage is. It is this side of the welder that is connected to the supply breaker. On the nameplate there will be a voltage, amperage both stated for an AC supply connection.


Would using a 200 foot extension cord which is 6 gauge 3 wire cord on a 220 single phase welder present any problems?

Absolutely, you will have voltage drop, maybe enough voltage drop that the welder will not work <<>> To do a voltage drop calculation for the 200 foot cable the input amperage of the welder needs to be stated. At a maximum distance of 201 feet and limiting the voltage drop to 3% or less, a #6 copper conductor can deliver 37 amps on a 220 volt system. Check the nameplate on the welder to see if it falls withing the range of 37 amps input amperage. Do not use the welders output amperage.


What does error code 23 mean Plymouth Voyager 1999?

CODE 23** Indicates that the air temp sensor input is below the minimum acceptable voltage or sensor input is above the acceptable voltage.


How many amps will a plasma hypotherm powermax 30 cutter draw?

It depends on the input voltage and amperage. It will run on 120 or 240 volts. All of this is detailed in your owners manual.


How much voltage AT89c51 can bear as input?

AT89C51 can have a maximum of 6.6v as input voltage