0
Can 2 20' 4 prong 30 amp cords be connected to make a 40' cord?
Wiki User
∙ 13y ago
Yes, 2 20' 4 prong 30 amp cords be connected to make a 40' cord.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you switch a 3 prong cord to a 4 prong cord on a dryer?
A qualified electrician should make the change to a dryer connection. The best way to cheaply make the change is to change the power cord on the dryer to the three hole standard.
Can you plug a 2 prong extension cord into a 3 prong extension cord?
I don't know about an extension cord, but they do sell plug adabters. You can pick them up at any hardware store or even Wal-Mart. They are ussaully grey or orange , and look like the plug end of the extension cord. One end will have the 2 prong, the other side will have the slots to plug in the three prong.
You are trying to change a 3 prong cord to a 4 prong your new dryer has two green cables attached to the inside of the dryer?
Dryer plug three to fourOpen up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
You should check electrical cords to make sure they are not what?
...worn to the point that bare copper wire is exposed, not frayed, not otherwise damaged. You could also check the temperature of the cord to make sure it isn't hot to the touch and make sure the plugs, sockets and connectors are not loose and the the connection points are undamaged. Often people cut off the third grounding prong in an appliance cord when they don't have the proper grounding outlet.
What is tightening the vocal cords?
Tightening of the vocal cords is also known as vocal cord dysfunction (VCD). This is a condition in which the muscles of the vocal cords tighten and this can make breathing difficult. It is caused by an autoimmune disorder.
Who sells 8' to 10' electric dryer cords?
in the USA 6ft is the longest pre-made cords for longer lengths, you will have to make a custom cord UL does not consider longer cords an acceptable solution
Is it possible to put a 4 prong plug on a dryer that uses a 3 prong plug?
Yes this is possible and for safety's sake highly recommended. Instructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the centre. From the centre wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
Are there 3 prong to 4 prong adapters for driers?
No, and adapters are not needed. What needs to be done in remove the old three blade dryer plug and install a new four blade cord on the dryer.Dryer plug three to fourInstructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
Is an electrical extension cord the same as a wall outlet?
The extension cord will extend the power outlet from a wall socket. The voltage will be the same at the end of the cord as it is from the socket. Be aware that extension cord may have a limit, as to how much current it can provide. The cord should be thick enough to provide as much power as the outlet can. It will then be properly protected by the circuit's fuse or breaker. A thin cord may get hot if a large consumer is plugged in, unless the cord is protected by it's own fuse at the plug end.
How many connection can you make with a usb cord?
If the computer is connected by a USB cord to a powered USB switch, then many connections can be made.
Is an adapter to go from a 3 prong dryer outlet to a 4 prong dryer cord available for purchase?
I would not recommend trying to use an extension cord for a dryer. the better option is to either buy a longer cord that is properly sized to deal with the extra distance or have an electrician come out and either move the outlet or custom make you a longer cord for your dryer.
What is linking cord?
It is like an extension cord for under cabinet lighting. Some lighting packages come with interconnecting cords that are too short for the cabinet layout to make placement look symmetrical. These cords can extend the range between the fixtures for placement of the fixtures where you want them to go, not where the manufactures length allows them to go. Make sure that you match the linking cord to the same manufacturer as the fixture so as to allow the socket ends will match.
